Traditional Culture Encyclopedia - The 24 Solar Terms - China V5 fault code daquan

China V5 fault code daquan

At the beginning of fault code P0, the fault indicates that the timing of camshaft position of cold start B of P054B is excessively delayed (line 65438+line 0), P02A6 fuel (air-fuel ratio) is adjusted to the highest limit-the low transmission ratio of second gear of temperature sensor circuit P0 122 throttle/accelerator pedal position sensor/switch A circuit p0732 of 4 cylinders P0A30 is incorrect. P0A5D drive motor A, U phase current P0B2 1 hybrid battery voltage monitoring D circuit high P0575 cruise control system input circuit P0AA8 hybrid battery voltage isolation sensor circuit range/performance P0504 brake switch A/ View the correlation of all results B. Fault code P 1 Starting from fault description P 1 530 ignition timing adjustment connector (Chevrolet) P 1682 Throttle control module/Engine control module (ECM)- Ignition power change P65438 monitor-Fault P 1643 Fuel pump-Low voltage P 168D Throttle actuator-Incorrect limping home position P1/kl. 4 Engine coolant temperature (ect) sensor-low voltage, Intermittent P 152D Idle Air Control Actuator-Signal Fault P 107B Variable Valve Timing (VVT) Overload Protection, Control Motor-Overheating P 1283 Accelerator Pedal Position (APP) Sensor 2 Fault code P2 begins with fault description P2806 Transmission gear sensor alignment (PRNDL input) P205E Reducer box temperature sensor circuit intermittent. Unstable P232 1 ignition coil h main control circuit low P2478 exhaust temperature out of range (row 1, Sensor 1) P2 10B throttle actuator b control motor circuit range/performance P2734 transmission hydraulic pressure control solenoid valve f electronic problem P204E reductant pressure sensor circuit intermittent/unstable P2049 reductant injection valve fault code P3 beginning fault description P3407 cylinder 1 exhaust valve control-circuit low P3468 cylinder 9 cylinder shutdown system/ Intake valve control-circuit height P3436 cylinder 5 shutdown system/intake valve control-circuit height P3408 cylinder 1 exhaust valve control-circuit height P3456 cylinder 7 exhaust valve control-circuit height P3470 cylinder 9 exhaust valve control-performance problem P3409 cylinder 2 shutdown system/intake valve control-open circuit P3493 cylinder 65438+ intake port-signal error- Intake valve control-circuit open to view all results Fault code B starts fault description B00B9 Driver's seat occupant position sensor C (sub-error) B0050 Driver's seat belt sensor (sub-error) B004 1 Third row left front (airbag). Stage 1 deployment control (suB- error) B 1890 passenger airbag disable (PAD) warning lamp circuit short circuit to battery B006 1 passenger seat belt tension sensor (sub-error) B0079 driver seat belt pretensioner b-start control (sub-error) B0039 right front, Row 2 (airbag) stage 1 deployment control (sub-error) B0002 Front driver (one side) (airbag) Stage 2 deployment control (sub-error) The fault code at the beginning of B2607U indicates that U0497 has received invalid data from the entertainment control module (rear A). U0004 high-speed CAN (Controller Area Network (CAN)) communication bus (+) voltage is too low. U0252 lost communication with the light control module (rear B). U0 146 lost communication with Internet connector A. U0587 (of water tank). Radiator anti-interference (tampering) device receives invalid data U0 157 and loses communication with information center B. U0 167 and automobile anti-theft control module U023C and picture processing module lose communication C. U0439 receives invalid data from all-terrain control module U3006. The control module enters the power supply A to check all the results. Fault description C00 Fault code begins with C. 0 1 Driving Anti-skid Traction Control (TCS) System (TCS) Control Channel A Valve 1 (sub-error) C0074 1 Brake pedal switch B (sub-error) C0082 Longitudinal acceleration sensor (sub-error) C0035 Right front wheel speed sensor power supply (sub-error)