Qichen T70 fault code set

The fault at the beginning of fault code P0 indicates that P0BF4 drives motor B, U-phase current sensor circuit high P0B74 hybrid battery voltage monitoring L circuit low P083A transmission oil pressure (TFP) sensor/switch G circuit P0BBE hybrid battery voltage change P00BF air flow (MAF) sensor B circuit range/performance-air flow is too high P0205 fuel injector circuit/open circuit-No.5 cylinder P0C04 drive motor B current high P0B8F hybrid battery voltage monitoring Q circuit intermittent/unstable P0726 engine speed input circuit range. Fault code P 1 starting from fault description P 123C air flow (MAF) sensor-signal high P 12A 1 fuel rail pressure sensor-signal low P 1662 turbocharger wastegate regulating valve-open circuit/short circuit to ground P/kloc-0. Kloc-0/700 Overdrive (O/D) Lamp-Circuit Fault P 1 654386-Low Heater Resistance P 163B Throttle Adaptation-Fault P 1506 Closed Throttle Position P 1 130 Heated Oxygen. The fault code P2 starts from the fault description P2204 intermittent fault of the NOx sensor circuit (line 65438 +0). P20BB reductant heater A control circuit low P2070 intake manifold tuning (IMT) valve stuck in the open position (line 1). P2742 transmission fluid temperature (TFT). Sensor b circuit low P2093 A (intake/left/front) camshaft position actuator control circuit high (second row) P2344 cylinder is higher than knock threshold P2738 transmission hydraulic control solenoid valve f control circuit low P2837 shift fork b position circuit range/performance P2600 engine coolant pump a control circuit/open circuit P253C (accessory power supply). Power output monitoring circuit low view all results fault code P3 start fault description P34 1/cylinder 2 cylinder deactivation system/intake valve control-circuit low P3403 cylinder 1 cylinder deactivation system/intake valve control-circuit low P3400 knock sensor-signal error P3449 cylinder 7 cylinder deactivation system/intake valve control-circuit open P3408 cylinder/. Fault code B starts with fault description B00DF Passenger Restraint Disable Switch (sub-error) B0097 Right Restraint Sensor 2 (sub-error) B0075 Second Row Right Seat Belt Pretensioner-Start Control (sub-error) B0084 Second Row Central Seat Belt Load Limiter-Start Control (sub-error) B009A Left Restraint Sensor 4 (sub-error) B0058 Third Row Right Seat Belt Sensor (sub-error) B2290 Occupant Classification System Fault B0074 Second Row Central Seat Belt Pretensioner-Start Control (Sub-error) B0093 View all results Fault code U Start Fault Description U0484 Received invalid data U0 1 1C from the lamp control module (later A) and lost communication with the rocker control module B U3004 accessory power relay U0030 vehicle communication bus A(+). Open circuit U0336 software is incompatible with restraint control module (airbag system). U0237 lost communication with digital audio control module. C U0 17F lost communication with seat belt tensioner module B. U0400 received invalid data U03 1 7 The software is not compatible with the handbrake control module U0420 received invalid data from the power steering control module to see all the results. The fault description at the beginning of the fault code C. C008A Driving Anti-skid/Traction Control (TCS) Mode Control (sub-error) C0074 Requested Driving Torque (sub-error) C0039 Anti-skid Traction Control (TCS) System (sub-error) C005 1 Steering wheel position sensor (sub-error) C0052 Steering wheel position sensor-signal A (sub-error) C0045 Brake pressure sensor B (sub-error) C0046 Brake pressure sensor A/B (sub-error) C003A Right rear wheel speed sensor (sub-error) C0054 Steering wheel position sensor-signal C (sub-error) View all results.