What are the performance characteristics of lifting lighting? What is the installation method of lifting lighting?

Lighting is often seen in our daily life. Lighting will be installed in many places, whether on the roadside or in high-rise buildings. In addition to these common places in daily life, there are some special places where lighting is used, and it is not ordinary lighting. Lifting lighting is a kind of professional lighting, which can adjust the height of the lamp according to the needs and can be lifted freely, which is very practical. The following small series will give you a detailed introduction to the performance characteristics and installation methods of lifting lamps, hoping to help you.

Performance characteristics of lifting lighting

(1) Lamp function: It is composed of four 500W high-efficiency and energy-saving Philips lamp holders, and each lamp holder can be rotated at a large angle according to the needs of the site to realize 360 omni-directional lighting; The lamp holders can also be evenly distributed on the lamp board to illuminate four different directions. If four lamp holders are required to illuminate in the same direction, the lamp panel can be turned over within 250 degrees in the opening direction according to the required illumination angle and orientation, and rotated about 360 degrees around the cylinder. The overall lighting is far and near, with high brightness and wide range, and the life of Philips bulbs is long.

(2) Irradiation range: 4 telescopic cylinders are selected for lifting adjustment mode, and the lifting height is 6m; Rotating the lamp holder up and down can adjust the irradiation angle of the light beam, and the coverage radius of the light reaches 35-55 meters.

(3) Lighting time: it can be connected to 220V mains for long-term lighting, or it can be directly powered by the generator set; Power is supplied by the generator set, and the fuel can be filled at one time, and the continuous working time can reach 13 hours.

(4) Convenient operation: every lamp within 50 meters can be switched on and off by wireless remote control, and the telescopic cylinder can be quickly controlled by electric or manual air pump.

(5) Applicable place: The lower tube of the lamp is supported by an adjustable tripod and can be reliably fixed on slopes, gravel roads and narrow areas not exceeding 15.

(6) Service environment: The whole structure is made of high-quality imported metal materials, which is compact in structure and stable in performance, ensuring normal operation in various harsh environments and climatic conditions, with rain-proof, water-drenching and wind-resistant grade 8.

method of erection

1. Install the U-shaped bracket

(1) Open the side door of the car body and remove the socket head cap screw at the installation position at the rear of the car body.

⑵ Erect the U-shaped bracket in the installation position at the rear of the car body, and the locating pin of the U-shaped bracket is located on the left side.

(3) Fix the U-shaped bracket at the rear of the car body with the hexagon socket head screws.

2. Install the drawbar

(1) jack up the front part of the car body with a bracket, and then open the side door of the car body.

⑵ Unscrew the bolt fixing the L-shaped bracket inside the car body with a wrench, and then pull out the L-shaped bracket.

⑶ Insert the drawbar into the car body and fix it on the car body with bolts, then put down the front support foot, adjust the support foot to a proper height, and then insert the fixing pin.

(4) Take out the chain in the carriage, hang it on the iron rings at both ends of the bottom of the carriage, and then hook the hook of the traction rod with the chain; Finally, remove the bracket.

3. Install the rear support feet

(1) Pull out the bolts that fix the rear support feet on both sides of the rear of the carriage, pull out the support feet to a proper position, and then insert the fixing pins.

⑵ Shake the rocker to adjust the height of the rear support feet, so that the wheels are off the ground and the weight of the car body falls on the support feet.

4, install the lighthouse lifting rod

(1) Lift the lighthouse lifting rod to the top of the car body and put it into the U-shaped bracket, and ensure that the bolts in the U-shaped bracket are inserted into the positioning holes on the lifting rod.

⑵ Introduce the six-core cable and four-core cable on the lifting rod into the car body through the large and small Glenn connectors on the car body respectively, and connect the cables as shown. Connect well, pay attention to the one-to-one correspondence of cables; Pay attention to the packaging when installing, and tighten the Gulen joint to ensure the sealing effect.

(3) When installing two cables, attention should be paid to leaving a margin of 15-20CM outside the car body to avoid the cable being stressed when the lifting rod is lifted.

5. Install the wire rope

(1) Remove the two locating pins on the pulley at the front end of the car body and the pulley and locating pin at the front end of the lifting rod.

⑵ Pass the wire rope on the winch in the car body through the square hole at the pulley position at the bottom of the car body, pull it out from the lower groove of the pulley, and then take it from the front of the lifting rod? Bypass the lower pulley, install the pulley at the front end of the lifting rod, then pull the wire rope back to the upper hole of the pulley at the bottom of the car body and use the pin? Shaft fixing wire rope. Pay attention to ensure that the direction of the clamp at the front end of the wire rope is oriented, and ensure that it is in a clamping state and cannot be loosened.

(3) Install the pin shaft at the upper hole of the pulley at the front of the lifting rod to prevent the wire rope on the pulley from falling off.

6. Install the lamp holder

(1) Unscrew the bolt that fixes the lamp holder on the top beam of the lifting rod; Then adjust the mounting brackets of the four lamp caps to a horizontal position.

⑵ Fix the four lamp holders on the beam in turn.

(3) Connect the input cables of the four lamp holders into the junction box at the top of the lifting rod, and connect them as shown in the figure; Pay attention to the wiring sequence of the four lamp holders? Install the junction box cover.

The above is what Bian Xiao found for you about the performance characteristics of elevator lighting and how to install elevator lighting. I believe that after reading Bian Xiao's introduction, you must have a general understanding of the performance and installation of elevator lighting. ? Lifting lighting has many characteristics, and it is very professional and practical regardless of the remaining lighting range in the irradiation time. However, it is very difficult to install this professional lighting tool, which requires step-by-step operation to ensure the lighting effect.