Disassembly and assembly of Ford Explorer gasoline filter element

Ford Explorer needs professionals to replace the steam filter. Replace step: 1. Open all the cushions in the trunk and you will find a black lid. Open it with a Phillips screwdriver and you will find the fuel pump body. The plug on the left is a wire, and the plug on the right is an oil circuit. Unplug the plug on the left first, and then start the steam. ...

Ford Explorer gasoline filter disassembly drawing

Ford Explorer needs professionals to replace the steam filter. The replacement steps are as follows:

1. Open all the cushions in the trunk and you will find a black lid. Open it with a Phillips screwdriver and you will find the fuel pump body. The plug on the left is a wire, and the plug on the right is an oil circuit. Unplug the left plug first, and then start the car several times to unload the oil pressure in the oil circuit;

2. The right oil circuit plug is a quick connector, which can be squeezed out by pressing both sides, but although the oil pressure is removed, there is still a lot of oil leakage. But it doesn't matter, it's next to the chassis, just outside, so don't worry about the smell of gasoline inside the car. The screw next to it is removed with No.8 sleeve, and it should be twisted obliquely when it is finally installed to ensure good sealing. Before taking it out, it is best to make a straight line mark corresponding to the cylinder in a white place to prevent dislocation when putting it back. The black steel ring is used to compress the oil pump assembly, and there is a sealing ring under it. Before putting it back, confirm whether the sealing ring is installed properly;

3. Put the oil pump assembly with the replaced fuel filter back into the oil tank. The sealing skirt of the fuel pump should be lubricated with vaseline, so as to avoid the leakage of fuel or gas due to the untidy sealing after the sealing skirt is twisted. Then, install the retaining snap ring of the oil pump and pre-tighten the snap ring with special tools according to the standard torque in the manual. Install the oil pump plug and fuel pipe on the oil pump and test for leakage. If there is no leakage, the seat can be installed. If there is leakage, the sealing apron should be reinstalled.

4. This kind of gasoline filter generally uses pipe code (throat code) to fix the oil pipe above the fuel filter to prevent the oil pipe from coming out. The first step to replace the filter is still to pull out the car key and disconnect the oil pump line or power supply of the vehicle. Then, loosen the pipe code at the outlet end of the filter, pull out the oil pipe and install it at the outlet end of the new filter, and lock the pipe code; Then do the same at the inlet end of the filter. Connect the gasoline pipeline to the new filter, and after checking that the pipeline is firmly installed, you can put the filter back in place and fix it. Fuel filter with quick-connect interface and oil return pipe: For the quick-connect interface fuel filter commonly used in European and American cars, the replacement method is similar to the straight-in and straight-out gasoline filter mentioned above. When replacing, you need to know the structure of the interface first, and don't pull the pipe with brute force. At the same time, pay attention to the position of each oil pipe, and don't connect it backwards, otherwise you can't get on the bus;

5. Remember to unload the oil pressure when pulling out the tubing. Be steady when you spill the oil, don't panic. Let it flow outside. Be careful when you take it out of the tank and put it back. Oil slick and sensor are not well scratched (crooked). Please remember where the two stainless steel columns on the top cover of the oil pump assembly are stuck in the oil pump body. It is best to mark the position of the main body first, and pay attention to the inclined direction of the top cover; Two plastic pipes should be installed in the correct position, the ones with sealing rings must be put back, and the ground wire plug under the oil filter must be inserted back; Finally, smoking must be banned! Replacing the fuel filter integrated in the oil pump assembly requires disassembling the whole oil pump and a special oil pump disassembling tool, which is not recommended for ordinary users. Does Ford Sharp have a first aid kit?

Ford Sharp doesn't have a first aid kit. Ford Edge is a medium-sized crossover SUV, which is built on the Ford CD3 platform and belongs to the Ford global mid-level car platform. It has two layout modes: front drive and four-wheel drive. Xinjie adopts atmospheric design, and the new hexagonal air intake grille is integrated with large-size full LED headlights. The front face/side skirt/rear spoiler are all designed in black, and the body lines are more elegant and smooth. At the same time, the new car comes standard with the largest 12.8-inch vertical central control panel in its class. Through the SYNC+ Zhixing infotainment system jointly built by Baidu, intelligent navigation superior to mobile phones can be realized, including fuzzy search of destinations, precise positioning navigation in the case of weak network or no network, and multi-destination navigation. SYNC+ can also interact with car owners in real life to help control air conditioning, entertainment content playback and other scenes. Ruijie Luxury Series is equipped with Ford Co-Pilot360 intelligent driving assistance system, full-speed intelligent adaptive cruise control system, intelligent induction braking protection system, emergency avoidance steering assistance system, lane keeping assistance system, post-collision braking assistance system, intelligent navigation assistance system, blind spot monitoring system and active parking assistance system. , thus helping car owners to avoid the troubles of complex road environment, and some models have reached the L2 automatic driving level, bringing a safer and more comfortable driving experience. The new car also has a complete passive safety system, including an ultra-rigid boron steel body. The A-pillar, B-pillar, door anti-collision beam, front and rear anti-collision beams and other key parts are made of high-strength steel, in which the strength of the front anti-collision beam is as high as 1300Mpa and the strength of the rear anti-collision beam is as high as 1000Mpa. Combined with the reasonable design of the collapse box, the collision energy can be absorbed to the maximum extent and the safety performance can be improved. The new car also comes standard with 7 airbags/air curtains for more comprehensive safety protection.

Disassembly drawing of Ford Explorer gasoline filter @20 19