Traditional Culture Encyclopedia - The 24 Solar Terms - How to eliminate the fault code of Sic Bo d70p0222
How to eliminate the fault code of Sic Bo d70p0222
System fault range: none at present.
Applicable model: SicBod70
P0 122: electronic throttle position sensor 1# line low voltage p0 123: electronic throttle position sensor 1# line high voltage p0222: electronic throttle position sensor 2# line low voltage p0223: electronic throttle position sensor 2# line high voltage p2/kloc-0.
English meaning: Not at present.
P0222 fault code knowledge:
no
Cause and effect: p0 122: electronic throttle position sensor 1# line voltage is too low 0 1 DTC detection condition 01kloc-0/engine running.
Depends on etc operation mode. Diagnostic trouble code trigger condition 02-0 1 electronic throttle position sensor 1# line is grounded or open. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure. P0 123: electronic throttle position sensor 1# line voltage high 0 1 DTC detection condition 01-0/engine running.
Depends on etc operation mode. 02 DTC triggering conditions 02-0 1 electronic throttle position sensor 1# line is short-circuited to the sensor power supply line. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure. P0222: Line 2 voltage of electronic throttle position sensor is low 0 1 DTC detection condition 0 1-0 1 engine running.
Depends on etc operation mode. Diagnostic trouble code trigger condition 02-0 1 electronic throttle position sensor line 2 is grounded or open. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure. P0223: line 2 voltage of electronic throttle position sensor is too high 0 1 diagnostic trouble code detection condition 01-0/engine running.
Depends on etc operation mode. 02 DTC Trigger Condition 02-0 1 Electronic Throttle Position Sensor Line 2 is short-circuited to the sensor power supply line. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure. P2 10 1:etc drive steady-state diagnosis error 0 1dtc detection condition 01-0/engine running.
Depends on etc operation mode. Diagnostic trouble code trigger condition 02-0 1 electronic throttle position sensor power supply and ground fault. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure. P2 135: electronic throttle position sensor 1# and 2# line related faults 0 1dtc detection condition 01-0/engine running.
Depends on etc operation mode. 02dtc trigger condition 02-0 1 tps error value (actual throttle position-estimated value) >: 20%, or tps position: 5% > .02-02 duration; : 0.05 seconds. 03 Possible causes of failure 03-0 1 Electronic throttle position sensor failure. 03-02 Electronic Throttle Position Sensor Circuit Malfunction. 03-03 Engine control unit failure.
Suggested solution: 0 1dtc detection step: Make sure the battery voltage is normal before performing the following steps. 0 1-0 1 Turn off the start-stop button and all electrical appliances. 0 1-02 Connect the diagnostic instrument bds to the vehicle diagnostic interface. 0 1-03 Start-stop button is placed in "Run" mode. 0 1-04 read and clear the DTC with diagnostic tools. Tip: Use the latest software for testing. 0 1-05, turn off the start-stop button and all electrical appliances, and put the start-stop button in the "run" mode again after 3-5 seconds. 0 1-06 restart the engine for road test, so that the engine can run under various working conditions. 0 1-07 read the DTC with the diagnostic instrument. 0 1-08 If DTC is detected, there is something wrong with the vehicle. Please perform the corresponding diagnostic steps. If no DTC is detected, the previously detected fault is an accidental fault. 02 Diagnostic Steps: Tip: After troubleshooting, reconfirm whether the DTC and symptoms exist. 02-0 1 Disconnect the connecting plug T6 of the throttle controller, and check whether the connecting plug T6 is cracked and abnormal, and whether the pins are corroded or rusted. be
Clean the connecting plug and plug. no
Go to step 02-02. 02-02 Measure the continuity between pins T6/4 and T6/5 of the plug of the throttle position sensor. be
Go to step 02-03. no
The throttle position sensor is faulty. Replace the throttle controller. 02-03 Remove the electronic throttle assembly. 02-04 Pull the throttle manually, and measure whether the resistance between t6b/3 and t6b/4 pins of the throttle position sensor changes in three states: closed, fully open and from closed to fully open. be
Go to step 02-05. no
The throttle position sensor is faulty. Replace the throttle controller. 02-05 Pull the throttle manually, and measure whether the resistance value of the plug of the throttle position sensor between pin T6/4 and pin T6/6 changes in three states: closed, fully open and from closed to fully open. be
Go to step 02-06. no
The throttle position sensor is faulty. Replace the throttle controller. 02-06 Measure whether there is continuity between t6b/ 1 pin and t6b/2 pin of throttle position sensor plug. be
Go to step 02-07. no
The throttle position drive motor is faulty. Replace the throttle controller. 02-07 Disconnect plug t73a of engine control unit. 02-08 Measure whether the wires from t73a/67 to t6b/ 1, t73a/26 to t6b/3 and t73a/4 to t6b/5 are short-circuited or open-circuited. be
Repair faulty wires. no
Go to step 02-09. 02-09 Measure the wires of t73a/6 1 to t6b/2, t73a/3 to t6b/4 and t73a/39 to t6b/6 for short circuit or open circuit. be
Repair faulty wires. no
Step 02- 10. 02-0 10 Replace the engine control unit and conduct a road test; Re-diagnose, read the fault code, and confirm whether the fault code and symptoms exist. be
Look for reasons from other symptoms. no
Replace engine control unit.
Million car purchase subsidy
- Previous article:Cleaning Method of Ford Mondeo Throttle
- Next article:Summer solar terms font
- Related articles
- 20 15 February 14 is it spring or winter now?
- What are the climate types and characteristics in Jiangxi?
- What AliPay are the ancient poems of early spring rain and dew?
- How to choose the rail diameter of 1.5T oil to gas injection?
- How was the baby of 202 1 born?
- 23 years later, that day fell into a shadow.
- Is Hitachi Amstro a Fortune 500 company?
- Is there a demolition plan for Yunheqiao Community?
- Meihua composition
- Why is Tomb-Sweeping Day scheduled for April 5th? What solar term is Qingming?