Measures to save energy and reduce consumption in factories

Measures for energy saving and consumption reduction in the factory 1 In order to further strengthen the work of energy saving and emission reduction, the following energy saving and emission reduction measures are formulated in combination with the actual work in the office.

First, the office energy saving and emission reduction measures

(a) saving electricity

1. Try to play DVD or VCD with optical drive to reduce power consumption.

2. Computers that are idle or not used within two hours should be shut down in time to ensure that "people leave the office and the office is cut off".

3. The computer should be maintained and cleaned frequently, be dustproof and moistureproof, and reduce power consumption.

4, 20 minutes before work, turn off the electrical equipment such as drinking fountains, computers, printers, and unplug, disconnect the power supply.

5. The air conditioner should be used in strict accordance with the standard of 26℃, and the air conditioner must be turned off after leaving for more than half an hour to reduce energy consumption.

6, prohibit the use of office computers for entertainment activities.

(2) Energy conservation

1, the first draft of the document should be in draft mode as far as possible, reduce line spacing, use fine print, and save paper, ink and electricity.

2. Copying printing paper should be double-sided, and the copy paper after single-sided use can be copied or cut into note paper or draft paper with a blank surface.

3. Reuse the recyclable briefcase.

4, try to use the network * * * to enjoy each other's documents, or use email instead of paper documents.

5, toilet according to the amount of water needed to wash dirt, respectively, using large water flow and small water flow for washing.

6. Replace "running, running, dripping and leaking" faucets in time to reduce waste.

(3) other aspects of management

1, reduce or try not to use disposable paper cups.

2. Use ballpoint pens and pens with replaceable refills instead of disposable writing pens.

3. Use more paper clips and staples, and less solvent products containing benzene, such as glue and correction fluid.

Second, suggestions

(a) improve the management system related to energy conservation and emission reduction, strengthen daily supervision and inspection, increase supervision and inspection rewards and punishments, and form a long-term management mechanism.

(two) vigorously implement technological innovation, and actively promote the use of energy-saving and emission reduction technologies and equipment. For example, frequency conversion energy-saving devices are used for electricity, and energy-saving faucets or energy-saving water supply and drainage devices that are "turned on when people use them and stopped when people walk" are used for water.

(three) the implementation of e-government, reduce the number of official documents, advocate paperless office.

Measures to save energy and reduce consumption in factories. Office area:

1, office lighting.

(1) Use energy-saving power supply.

(2) selective switch, turn off the lights when going out.

(3) Do not use electrical equipment and appliances, and cut off the power supply.

2. Office air conditioning.

(1) Turn the air conditioner to 26 degrees and sleep more.

(2) Extend the air conditioning drainage pipe into a bucket, and you can receive a liter of water in 2 hours. The saved water can be used for watering flowers, washing hands and mopping the floor.

(3) Turn off the air conditioner about 1 hour when the temperature is suitable.

3. Office computer.

(1) If you don't use the computer for a long time, please turn off the host and monitor of the computer. During the short break, try to enable the "sleep" mode of the computer.

4. Office equipment.

(1) It is stipulated that everyone should buy a roll of paper (put it in the dressing room) to avoid the phenomenon of personal use of napkins.

(2) Use more pens and less disposable pens. The case of fountain pen is kept, and the refill is used continuously.

(3) Take good care of equipment and office supplies, reduce unnecessary damage, and improve the service life and efficiency of tools.

(4) Effective utilization and supervision of waste newspapers, waste electrical appliances and wastes.

(5) The transmission of office instructions in the hotel adopts computer network; Small fonts for internal documents, and both sides of the paper.

(6) There is no need to "one person and one piece" to reduce the purchase amount, and many people share it.

(7) Reduce the chances of using disposable cups, and personally prepare water cups and disinfection cups for visitors.

Second, the public * * * area:

1. Put a water-saving awareness card in front of the sink and a power-saving awareness card in each dormitory.

2, corridor lights are not fully open, take interval lighting.

3. The number of lamps in the employee elevator is reduced, and the lifting rate is adjusted. Encourage employees to take more stairs.

Third, others:

1, the new employee training invited the engineering department to tell employees about energy conservation and emission reduction, so as to raise their awareness of saving from the very beginning.

2. induction lamp is used for the street lights in the dormitory building, which shortens the induction lighting time.

3, employees uniform coat to reduce the number of cleaning, encourage employees to wash clothes by hand.

Chapter III Measures for Energy Saving and Consumption Reduction in Factory In order to actively respond to the spirit of energy saving and consumption reduction documents and do a good job in energy saving and consumption reduction, our company has formulated a specific annual energy saving and consumption reduction plan based on the principle of "cultivating consciousness and strict management", centering on the overall goal of energy saving and consumption reduction in the company and combining with the actual situation of the company.

By carrying out energy-saving and consumption-reducing activities, all employees can firmly establish resource awareness and conservation awareness, form a good habit of thrift, organize various publicity and education activities, publicize the importance of energy-saving and consumption-reducing work, and advocate frugal and civilized working methods. Everyone is a propagandist and implementer of energy conservation and emission reduction. Refine the main measures to save energy and reduce consumption, and strive to reduce energy consumption and expenses.

I. Target of 20XX Energy Saving Plan.

Start from yourself, start from bit by bit, cherish every kilowatt hour, every piece of paper and every drop of water, form a good atmosphere of saving for everyone, everything, everywhere and around, strive to reduce the overall consumption of water, electricity and office expenses by 10%, and initially establish a long-term mechanism for energy conservation and consumption reduction management.

Second, the specific content of energy saving and consumption reduction.

1. Water saving measures.

A. Turn off the tap in time after washing your hands;

B. Do the daily maintenance of plumbing pipes in time to prevent water leakage;

C. Clean water shall be used for product cleaning, recycling shall be done well, and sedimentation tanks and treatment facilities shall be built to realize the recycling of water resources.

2. Power saving measures.

A. Production equipment with high energy consumption should be phased out gradually, and environmentally friendly and economical equipment should be used when upgrading. All adopt energy-saving motors.

B, reasonably arrange production operation time, effectively utilize peak and valley values of electric power, and realize comprehensive utilization of electric power.

C. It is forbidden to use electric heaters with high energy consumption and electric appliances with fast heating;

D promote the use of energy-saving light bulbs in offices and work areas, so that the utilization rate of energy-saving light bulbs can reach more than 85%;

E. Make full use of natural lighting during the day and minimize the use time of lighting equipment;

F. Turn off the lights when you leave the workplace;

G. Minimize the standby energy consumption of equipment, and turn off electrical equipment such as printers when they are not used for a long time;

H. Turn off the power of all equipment when off duty;

3. solar terms measures.

A. Reasonably arrange the service time of air compressor equipment, minimize idling of equipment, improve the service efficiency per unit time and reduce gas waste;

B. Check whether the pipeline leaks before work, and handle the existing problems in time;

4. Office supplies saving measures.

A vigorously promote the use of recycled paper, advocate double-sided paper, and try to modify manuscripts on the computer to reduce paper consumption;

B. Make full use of the advantages of e-government, use network office as much as possible for internal documents, reduce the use of paper, and strive for paperless office;

C. use less or no disposable paper cups;

D improve the procurement and distribution system of office supplies and pay attention to energy conservation and environmental protection.

E. strictly control the use of printer cartridges and ribbons.