Mijia intelligent bath heater experience: more in line with the use of young people's needs

In recent years, the warm air bath heater has gradually replaced the traditional light bulb bath heater. Recently, Xiaomi launched a Mijia intelligent bath heater product, using dual-core rapid heating, only one minute can be warmed up to 10 degrees, and the use of wind heat heating, can keep the whole bathroom warm. At the same time, you can access the Mijia APP to realize the intelligent experience. Today to share with you the experience of using it in recent times.

Mijia intelligent bath heater experience: more in line with the needs of young people

Appearance installation

The bath heater is divided into two components, the host and the panel. The host part of the light gray shell, the material is relatively thick, and the workmanship is also very good, the shape is regular, no burrs and other defects. Positive depression there are two motors, can realize the warm air and ventilation function at the same time open. The other side of the long grille is the air outlet, built-in 2400WPTC ceramic heating module.

Additionally, there is a cover plate designed in the corner of the recessed area, which is the installation of terminals to prevent the line from moisture; the other side of the interface is used to connect to the panel, power supply for the lights and signal transmission needs. Around the body is also installed with 6 buffer foam, reduce the motor running with the ceiling and panel vibration. The side of the body is affixed with a self-adhesive nameplate, labeled with the technical parameters of the bath heater and circuit diagram.

The wider side is reserved with an oval air outlet, which is connected to the aluminum foil ventilation pipe after installation to ventilate the air through the house exhaust channel.

Buy Mijia intelligent bath heater, at the same time purchased the installation service, after the arrival of the master received a call, the master in accordance with the previously scheduled time on time. Check the bathroom environment to confirm and ceiling situation, confirmed that can be installed after the start of hands. First of all, help me remove the old bath heater installed by the previous landlord, by the way, the original line was cut off and wrapped processing, Mijia intelligent bath heater is a wireless remote control, so the original wall switch as well as the inside of the wire is not needed.

Then install the non-return valve and aluminum foil vent pipe in the ceiling, connecting with the room's reserved exhaust channel. Then install the four integrated ceiling clips to the main unit, put the whole bath bomb into the ceiling, connect the power supply to the main unit and fasten the protective cover. After organizing the wires in the ceiling, put the bath bar back in place and install it, you can move around to adjust the position, and finally connect the cover wire and the host, buckle to the roof on it.

Mijia intelligent bath heater with standard 60x30 cm specifications, and the host part of the thickness of only 9.25 cm, for the integrated ceiling environment is very easy to install. But if your home bathroom is a traditional PVC ceiling, you need to additionally match the conversion frame to install.

After installation, the panel is flush with the ceiling and fits tightly, and the white panel looks very simple and fits perfectly with most modern home styles. The long grille on one side of the cover is the air outlet, which corresponds to the air outlet grille on the body, and the 52-centimeter wider design helps accelerate heat dispersion. On the other side is a large light panel with an air intake grille set aside around the panel. Inlaid in the center is a row of function indicator lights and emergency buttons, turn on the corresponding function port indicator lights on.

Wireless remote control simplifies the installation steps, the use of the remote control and the bath master need to match, bath master power, long press the remote control on the "warm air low" and "ventilation" key, the remote control blue indicator light flashes into the pairing state, wait a moment! Wait a few moments, the bath heater issued a "beep" sound prompt, the remote control blue indicator light is always on for 5 seconds and then off, that is to say that the pairing is successful. In order to cater to the daily use of habits, the wireless remote control also adopts the standard 86 models, remove the back cover plate fixed in the wall socket, and then the remote control and the back plate can be fastened.

The remote control's button layout is also relatively intuitive, with the screen removed compared to the previous Pro version, and includes eight commonly used function buttons for Warm Air High/Low, Demist, Ventilation, Dry, Blow, Light, and Stop.

Using experience

Originally, the function of the bath bomb is relatively single, and then gradually become a composite function of the product after continuous improvement. First of all, the main heating function, especially in the northern winter bath time is just needed. Mijia intelligent bath heater is equipped with 2400WPTC ceramic heating module, open the heating function can be warmed up to 10 degrees in 10 minutes, the acceleration speed is very fast, and can significantly reduce the waiting time before taking a bath.

In addition, it supports high and low heating temperature adjustment, so you can choose the right temperature gear according to the season and room temperature. With the 52mm elongated air outlet design to increase the amount of warm air outflow and coverage area, the whole bathroom realizes the top-to-bottom waterfall warm air duct, and the heat is blown from the head to the soles of the feet, which also enables the whole bathroom to warm up quickly. Measured after 1 minute of opening the low-grade warm air, the temperature of the air outlet is 65.1 degrees; after 1 minute of opening the high-grade warm air, the temperature of the air outlet is 88 degrees.

Close the bathroom door to keep relatively closed, open the warm air before the bathroom temperature is 26.2 degrees, with a low-grade warm air heating run for 10 minutes, the temperature of the bathroom rose to 30.5 degrees, visible heating capacity is very excellent.

When taking a shower, a large amount of water vapor quickly fills the entire bathroom, fog and water droplets appear on the surface of mirrors and sinks, and some users can also experience the phenomenon of dizzy showers. After turning on the defogging function, the water vapor in the air can be quickly displaced from the ventilation ducts. Thanks to the dual DC motors, the warm air and demisting function can be turned on at the same time, removing moisture while warming up the bath.

When you leave the bathroom after taking a shower, it is recommended to switch to dry mode, which continuously discharges the moisture from the room and keeps the bathroom in a relatively dry state. Usually when you go to the toilet squatting large open the ventilation function, you can accelerate the odor out, remove the odor of the bathroom. In summer, when you go to the bathroom or wash some clothes in the bathroom is relatively hot, you can also open the blowing function as an electric fan.

Lastly, the lighting function is commonly used, easy to do the lighting itself is the main, the lighting of this bath heater is not bad. Embedded LED lamp beads in the body, with a large area of the light guide plate, high light brightness, irradiation range is also very wide, like my rental room 4 square meters of bathroom enough. Normal turn on the lighting to the highest brightness exposure, the color temperature remains at 4000K, natural warm white light, bright and not harsh. Ra90 high color rendering index can more accurately restore the original color of the object, convenient for girls in front of the washstand make-up.

Through the cell phone APP can realize the light brightness infinitely adjustable, after turning on the night light mode, you can set the time period for the night light to turn on and off, and turn on the light in the time period, the light runs at the lowest brightness, and the light can be illuminated at night, but not particularly blinding.

Intelligent experience

He room to maintain a consistent intelligent experience. In the Mi Home APP home page click on the plus sign in the upper right corner, scan the QR code on the manual to add a new device, long press the emergency button on the bathtub for 7 seconds to reset, and complete the networking configuration according to the wizard guidelines.

The device management interface is very simple, the functions and modes of entry are distributed in a modular form, which is clear at a glance. The lighting and stop buttons are independently distributed, maintaining a layout similar to that of the remote control. In the center, there are two warm air switches and switches for the other four modes; the brightness adjustment is presented in the form of a slider, supporting infinite adjustment, which can only be operated when the lighting is turned on.

At the bottom are the options for bath delay and lighting delay, also presented in the form of a slider. The delay can be set up to 120 minutes for the bath bomb and 90 minutes for the lighting, and the corresponding function will remain delayed for a period of time after it is set and turned off. For example, after a 15-minute delay to turn off the ventilation function after a large number, people leave the bathroom after the odor will continue to exhaust away.

In addition, through the Mijia APP can also realize some intelligent functions, such as setting the timer to open the ventilation, every morning automatically run 3-5 minutes ventilation function, the daytime bathroom when the air is better. You can also set up in the smart scene and other Mi system smart home products linkage, such as adding a human body sensor, when a person is detected walking near the bathroom door, automatically turn on the light of the bathtub.

Experience summary

From the perspective of the traditional bath heater alone, the performance of the Mijia intelligent bath heater is already outstanding. Standard specifications to adapt to different ceiling environments, simple and stylish face value and modern home style match; wireless remote control to eliminate wiring cumbersome, convenient operation of the large buttons; equipped with 2400WPTC ceramic heating module, with 52cm long out of the style grille, high and low two-grade adjustable, fast heating speed, wind distance; built-in dual motor, warm air and ventilation can be turned on at the same time; four major independent functions to meet the daily bathroom ventilation and air blowing. Independent function, to meet the daily bathroom ventilation and deodorization needs; 4000K color temperature lighting module, Ra90 high color rendering index, brightness is soft and not harsh, low illumination mode at night more intimate. And access to Mijia APP to achieve intelligent experience is the icing on the cake, mobile APP remote control, smart home linkage, small love classmate voice control and so on more in line with the use of young people's needs.