Video tutorial on how to install wired surveillance camera

How to install wired monitoring by yourself?

How to install the surveillance camera by yourself: prepare the wireless router, prepare the tf card and install the relevant mobile phone software. Have a wireless router ready, because most home surveillance cameras usually support wireless functions.

The rated voltage of the wire for monitoring camera should be greater than the working voltage of the line; The insulation of the conductor shall conform to the installation mode of the line and the environmental conditions for laying. The cross-sectional area of the conductor should meet the requirements of power supply and mechanical strength. When wiring, try to avoid wires with connectors.

Assemble the camera, install it in the required position, and connect the network cable and power cord. The power supply is 12V DC power supply, which can be centralized or independent. An adapter from 220AC to 12v DC power supply is installed on the camera. Connect the host, monitor, camera, switch and power supply.

Install ip scanning software of digital camera; Log in to the camera, just configure the camera and change the storage mode. In addition, if large-scale monitoring is done, manufacturers must choose the right one. Long-term cooperation is the most important, and the circuit diagram must be kept after completion. This allows for post-maintenance issues.

And make sure it is firm; Insert the power output plug of the power adapter into the power socket of the monitoring camera and make sure it is firm; Connect the other end of the cable to the control host, and ensure the connection is firm; Connect the power supply of the monitoring host and the camera, adjust the camera to a specified angle through the monitor, and the cable monitor will be installed.

On-site monitoring and installation: entrance and exit control, monitoring products, comprehensive monitoring and prevention. Supermarket monitoring installation: equipped with stable transmission POE switch, 16 recorder, X-series POE camera, convenient without jamming.

Can the infrared camera really monitor the video?

Infrared camera refers to the kind of camera that can be monitored 24 hours a day. There are also ordinary infrared cameras and dot matrix infrared cameras. Dot-matrix infrared camera is better than ordinary infrared camera, with long irradiation distance, fine and clear image quality and longer service life.

The infrared monitoring camera can see the monitoring picture through the infrared light at night. The infrared light emitted by the infrared lamp is used to illuminate the object, and the infrared light is diffusely received by the monitoring camera to form a video image.

Yes Infrared cameras can see people clearly at night, so most night vision surveillance cameras use infrared cameras. Because the shooting principle of infrared camera is different from that of ordinary camera, the infrared lamp emits infrared light to illuminate the object, and then the infrared light is diffusely received by the monitoring camera to form a video image.

How to install surveillance camera with network cable

1. It's actually easy to install a network surveillance camera. Just install the network camera in the corresponding position and plug in the network cable and power cord. Let me show you a schematic diagram. However, it is easier for NPC to monitor the camera. It transmits the network through wires. Installation is super simple, just plug in the power supply and you can use it.

2. Determine the installation position of the camera, install it, and connect the power cord and network cable. Download the corresponding monitoring software on the computer, open the equipment list, find the model and name of the camera, and manually connect to the network.

3. Installation steps of home camera: Step 2: Determine the installation direction of monitoring camera and the location of monitoring back-end equipment (hard disk video recorder and monitor). Then start the wiring work step by step. Then install the camera bracket where the surveillance camera is installed.

Installation steps of cable camera

The rated voltage of the wire for monitoring camera should be greater than the working voltage of the line; The insulation of the conductor shall conform to the installation mode of the line and the environmental conditions for laying. The cross-sectional area of the conductor should meet the requirements of power supply and mechanical strength. When wiring, try to avoid wires with connectors.

Summary Install the chassis of the camera on the bracket, and then install the camera on the bracket. Connect the power plug and the camera plug. Connect the BNC cable to the BMC interface and tighten it with a screwdriver. After the two ends are connected, connect the camera to the computer host or camera hard disk.

Prepare camera, bracket, video cable, 12V power supply, acquisition card, etc. Determine the location where the camera is installed to avoid interference caused by mitigation; Arrange the camera circuit to connect it with the indoor computer; Turn on the power, set up the camera, and you can start using it.

Installation steps of wired cameras: For wired surveillance cameras, first determine the installation location to ensure that the surroundings will not be disturbed by the environment. After determining the location, we will carry out wiring, and there are many ways of wiring.

On-site monitoring and installation: entrance and exit control, monitoring products, comprehensive monitoring and prevention. Supermarket monitoring installation: equipped with stable transmission POE switch, 16 recorder, X-series POE camera, convenient without jamming.

Video tutorial on the steps of installing surveillance cameras

1, the video tutorial of the steps to install the monitoring camera is as follows: Step 1, prepare the monitoring hardware equipment, camera power supply, crystal cable clamp, video recorder hard disk, eight-port switch, camera bracket and self-tapping screw display. Step 2, locate and determine the location where the camera needs to be installed, and determine the location where the video recorder and monitor are placed.

2. Determine the installation orientation of the monitoring camera and the location of the monitoring back-end equipment (hard disk video recorder and monitor). Then we started the first step of work wiring. Then install the camera bracket where the surveillance camera is installed.

3. Prepare to install camera accessories, including pliers, screwdriver, camera, camera charger, camera bracket, chassis and BNC connector, and connect BNC cable. Pick up the camera bracket and install the chassis on the bracket. Now install the camera on the bracket. Check whether the power supply is the camera power supply.

4. The installation tutorial method of Xiaomi surveillance camera is as follows: Tools/raw materials: Xiaomi MIUI Mijia 70 1. Open Mijia app and click+in the upper right corner. Select the model of Xiaomi camera used.

5, adjust and determine the bracket installation position, drilling installation screws. Fix the screws on the top of the camera to ensure that the camera will not shake. The network cable is connected to the network port terminal of the camera, and the power cable is connected to the plug. The computer logs into the camera monitoring screen and adjusts the screen and angle of the monitoring camera to the best.

6. The fixed position of the camera is very important. What kind of camera are you going to buy? The main parameter of the camera is the effective distance.