Traditional Culture Encyclopedia - Traditional culture - How to wire a concealed wiring installation? How to wire concealed wiring wiring method
How to wire a concealed wiring installation? How to wire concealed wiring wiring method
First, how to install concealed wiring
How to install concealed wiring wires? Many users do not understand the problems associated with the wire. The following is a small introduction to the issue of wire concealed installation alignment. Users who need to come to a brief understanding of the concealed installation alignment!
1, before the construction of wires, decoration personnel will be the world indoor line to the drawings, to confirm the rationality of the alignment and feasibility. In case the installation process has begun to find the design is not feasible.
2, in accordance with the direction of the map to confirm the location of lamps and sockets and switches, and then draw the direction of the ground to confirm the location of the wires, and through the walls and the location of the floor, as well as the beginning of the corner branch and terminal points.
3, according to the previous markings made on the ground wall to start digging wall grooves. Pay attention to the width and depth of the groove to be able to bury the wire pipe.
In the location of the hole through the wall to the wire pipe carefully bent, to do so after bending the pipe can still be threaded inside. Then use the special rolling head or riding nails fixed to the wall.
4, there are sockets and switches in the location of the first hole pre-buried plastic expansion pipe or play a good wedge. But this outlet will protrude on the wall. Now most users do not utilize this method.
Now the common method is to bury all the sockets and switches of the junction box to the wall, only the sockets and panels leak out of the outside.
5, in the threading, the more formal practice is to use steel wire first through the past, and then in the wire pulled through. In the house decoration can directly wear the wire to the sheath tube, but in the turn of the place will be more difficult to go through. So the common method is to put the plastic pipe at the same time also wear the wire, or in the plastic pipe first pre-threaded a lead wire spare.
6, after all the wires are worn, and switches and sockets connected to the lamps and lanterns for power test. Confirm that all the socket lines are fully energized can be previously chiseled walls and floors using cement mortar to repair the square rectification can be.
Second, how to connect the concealed wiring wiring method
Concealed wiring how to connect it? Many users do not understand the method of concealed wiring. The following is a brief introduction to the concealed wiring how to wiring method. Users who need to come to a brief understanding of it!
Concealed wiring lines are usually 7 branches of the route: including power lines, lighting lines, air conditioning lines, and TV feeds, telephone lines, = computer lines, and alarm lines.
The upper part of the bedside table should be left with a power line interface, and the use of 5-hole plug board with a switch is appropriate to reduce the trouble of bedside lamps without a switch, but also want to leave a telephone line port, if it is a double bedside table, it should be in the upper part of the two headboards respectively, reserved for the power supply and the telephone line port.
The dresser should also be reserved above the power port, in addition to consider the dresser mirror above the reflective light, so in the wire box next to the addition of a switch. Writing desk or computer desk should also be installed above the power line TV feed computer line and telephone line interface.
The wiring is connected to three lines, including the power line, lighting line, and air conditioning line. Try to leave two or three power connections for the power cord.
The best choice for lighting is to choose a warm color light source, and the light switch is located on the inside of the door. The air conditioner also needs to be equipped with ports according to the requirements of the professionals.
Third, how to change the wire dark line
How to change the wire dark line? Many users do not understand the method of wire dark line change. The following is a small introduction to the method of wire dark line. Users in need of a brief understanding of it.
1, with the ground instead of
The method of replacing the wire with the ground applies to the socket circuit, the zero line or the fire line leakage occurs. The limitations of this program are relatively large, but this method can be used not infrequently.
2, wire threading
The wire threading method applies to a shorter distance or decoration of the pre-buried wire threading.
If in the process of decorating the pre-buried threading wire, you can directly like a needle and thread, the new wire along the threading wire can be pulled in. It should be noted that when wearing into the new wire, to wear into the new threading wire at the same time to prevent future problems.
If you can, try to pull the old wire out of the conduit. If you can't pull it out, leave it in the conduit.
If you don't have a pre-built steel wire during the renovation, you can try to use it during the repair. Wire threading steel wire into the pipe, than the wire directly into the better operation. If the distance is shorter and the angle is smaller, this approach can be operated.
3, hard pull
If you do not use the wire, you can use the old wire as a wire, directly pull the old wire out of the hard pull, while the introduction of new wires can be.
4, take the open line
If the line can not be operated then it can only take the open line. Bright line to choose the number of cores and the need to replace the same number of wires. After the completion of the wiring to use the wire card or wire groove will be fixed on the wall wires can be.
The above is about the wire concealed installation how to route, concealed wiring how to wire the method of wiring the relevant content, I hope to help you! Hunting decoration network, China's well-known large-scale decoration square table, decoration leading brand. If you want to put some thought into the design of the decoration, we recommend that you apply for the free design service of the hunting network, through the professional designer's on-site room measurement to help you plan a reasonable space layout and exquisite design.
>> Click here to get a professional designer free room measurement design
- Previous article:Five Selected Works of Tomb-Sweeping Day Sacrificial Sweeping Activities in 222
- Next article:How to pronounce bell house?
- Related articles
- Some famous classical music
- How to make leek buns delicious?
- Inheritance of traditional culture
- Shimen village belongs to which province and which city.
- "Zunyi: Listening to the Echo of History
- The weaving method of the twist scarf
- The Origin and Development of China Railway
- What happened to the second infection of the new coronavirus? How did WHO respond?
- How to explore a variety of games in the materials of kindergarten teaching and research meeting
- How about small-scale storage hosting in Shanghai?