What should I do if I can't retract my fishing rod?

Question 1: What if the rod can't be retracted? 60 points 1.Raw knocking method (most commonly used), open the rod tail cap, find a concrete or hardwood board, stand the rod tail on it, then hold the rod in one hand, and the other hand hold the stuck rod knuckle and knock hard downward, generally can be knocked open. If the line ring falls off, you can re-glue it.

2. Thermal expansion method, use boiling water to pour the following section of the thick, and then use a cloth to hold both sides of the rotation.

3. Clutch the two sides with thin rubber and turn them with force.

Question 2: What if the rod doesn't shrink back (urgently) Put a drop or two of vegetable oil on the joints of the rod, and then gently rotate the upper and lower rod joints when the oil seeps in a bit. :handshake

Problem 3: How to put the rod back Method 1: If the rod is stuck, break it down and take out the stuck section, find a flat place or a rock, put a few layers of cloth on it, and then hold the stuck sections tightly, and then force them to the ground or the rock a couple of times, paying special attention to the verticality of the rod body when it is under the rod, and then the stuck part of the rod will be loosened.

Method two, the stuck rod two sections flat on the table, with a hairdryer against the card section of the place (thick section) repeatedly blowing, feel the rod card section a little hot, gently rotate the force can be unscrewed.

Method three, with boiling water poured on the stuck part of the thick section of the expansion of the heat, but do not pour to the details, and then dry and then rotate the two rods connected to make it loose.

Method 4, the two sections of the rod stuck upside down, thin part up, thick part down, with sewing machine oil (oil, kerosene can be) along the dry wall of the tube on a few drops to let it slowly infiltrate, and then put the rod aside and wait patiently for a day or two, wrapped in a cloth at the card joints, gently on the few times to rotate hard to loosen, basically, can be separated.

Fish in the water outdoor for you to answer

Problem 4: how to shrink the rod back to wear thin rubber gloves, the rod will be standing on the ground, the left hand force to hold a section of the outstretched, the right hand down to hit the left hand tiger's mouth can be outstretched back. The main point is that the direction of force must be parallel to the rod, with instantaneous impulse, the force does not have to be too large.

Problem five: the rod shrinks back Once out of the "card section", how to deal with? Fishing newspapers and magazines often have how to deal with the rod card section of the article published, the promotion of a variety of methods, there are: stomping method, knocking method, twisting method, pincer method, hot and cold shrinkage method, and even the use of broken "limb" method as a last resort. It should be recognized that some of these methods is indeed a rule of thumb, often works. But according to observation, there are many failures, or although successful, but make a good end of the hand rod scarred, leaving internal injuries hidden, it is a pity. Mend the sheep, is especially not too late, but can we save for a rainy day, before it is too late? Some anglers summarize a very simple and effective method, can indeed prevent the rod card section. This method only need to prepare a candle, with wax coated in the parts of the prone to card joints, in order to make the wax oil coated uniformly, you can light the candle, so that the melted wax oil drops on a piece of cloth, and then use this cloth to wipe the rod joints. After using this method, even if the big fish, hanging on the obstacles, so that the tip of the force, or sun exposure, rain water immersion, there will be no card section phenomenon due to the occurrence of their self-proclaimed that this method is the rod card section of the nemesis. Anglers want to avoid the pain of card section, may wish to try. In short, remember: card section can not be twisted with brute force after hard back, it is very easy to get split and cracked and even break the rod. I would like to introduce a very effective way to remove the jammed rod: the "dun strike method". Use the thicker sections of the rod to stand upright on the ground as a "guide tube", then throw the rod (with the thicker sections underneath) down the "guide tube" from a high place, and the acceleration of gravity will push the stuck section back down. Once can not, can be two or three times. Note that the "guide tube" should be long, the height of the person standing is not enough, you can stand on a stool. "Guide tube" under the mat must be smooth and flat (polished concrete or wood), and "guide tube" must be kept vertical with the mat. In this way, the rod's mouth will not be cracked. If the rod still won't go back after the above treatment, it means that the rod tip has been glued to the rod and it is unlikely to go back in the future. Is there no other way back? No, there is a way, and that is to use the method of "amputation and unbinding": file the upper portion of the stuck tip with a small file at a distance of 1 cm from the upper port, and make a deep cut, but do not hurt the tip, and then use a knife to gently remove the filed portion, which means that the sticky part of the stuck tip is opened up to a length of 1 cm. And then according to the above method of knocking vibration treatment, will certainly be able to rod tip back, and then file the saw kerf with a small file to file flat. The second section under the rod tip is sawed off by 1 cm, and there will be no problem from appearance to use. However, it should be noted that when the section of the mouth sawed off 1 cm, the mouth of the section becomes larger, and then look at the tip of the rod in the interface remains how long, such as connecting part of more than 4 centimeters, can be used directly. If too short, we must try to thicken the lower end of the rod tip, you can hang a layer of "502" glue in the place, or smear some other adhesive can be cured, in order to lengthen the length of the rod tip in the socket. Attention should be paid to: smear adhesive rod tip, must be dry before use. Here also remind some new anglers, is to close the rod, must be a section from the bottom up to close, can not close the rod tip first, resulting in the first bottom of the rod tip, wrongly inserted into the other rod joints in the seam, so that the tip of the rod is easy to position after the card, so that a tube loaded with two sections, if you will not be able to plug into the rod section and then inserted into the rod is equal to the rod will be the ends of this section of the rod to hit the wedge, the more inserted tighter and tighter, and some of them thus destroyed the rod. In this case, can not be inserted again, but to try to be stuck pole section out, can be a small stick or waste pole to the top, must be careful operation, the mouth of the section is most likely to top crack. Avoid this situation is also very easy, that is, each time you pull out the rod, first from the tip of the rod, a section to pull out; when the rod, from the bottom of the beginning, a section to close, there will be no wrong insertion phenomenon.

Problem 6: What if the rod pulls hard and doesn't go back? Take out the stuck two sections, pinch the thin end, vertically away from the ground one twenty centimeters, free fall, the ground pad a piece of cloth! Gently knock a few times, on the basis of not knocking the bottom section of the fishing rod, can be appropriate to add a little more strength, perhaps it will shrink back! The way is not very good, and there is no other way, anyway, every time I encountered this situation is how to deal with!

Question 7: How to solve the problem of the rod stretching out and shrinking how to solve what the rod, is not upside down stuck somewhere, you can try to stretch out completely first, and then section by section to shrink back. Hope to help you

Problem 8: the top of the fishing rod shrunk to get out how to do First of all, you can shrink back ah, and then use the bottom of the fishing rod suddenly to the ground warping, of course, you find a soft place, or not knocked rotten. It is by inertia to get him down. If you still can not get down, put some detergent, and then knock, still can not get down, you go to sell fishing rod store, in fact, that can be a section of a section to remove. Usually you can get it off by cocking it 2 times.

The first section of the fishing rod can not shrink how to do

The first section of the rod thought that the fish immersed in water is not easy to shrink back Don't be in a hurry to use brute force. Go home and unscrew the bottom cover, pull out section by section, wipe dry if you have the conditions to apply rod oil (Vaseline is fine) to dry overnight, can not be pumped so thoroughly air-dried, gently ton generally can be toned open.

Question 9: My telescopic rod has not been able to retract at the very end, what should I do in this case? 50 points on a little oil to rotate it

Question 10: the rod can not be put back how to The most simple and effective way is that you in the joints of the rod one or two drops of vegetable oil, and then wait for the oil seeped into some of the gently rotate the upper and lower rod joints can be. This method is very effective, you can try.