Traditional Culture Encyclopedia - Traditional festivals - What's the fishing method in kareem abdul-jabbar?

What's the fishing method in kareem abdul-jabbar?

With the continuous improvement of various fishing methods, the traditional hook fishing method has also changed from the initial single lead-tin welding to the current copper-clad welding. Under the brainstorming of many fishermen, from the previous external thread to the current internal thread, the thread binding method was invented. Although the hanging fishing in the stocking pit of the competitive pool still occupies the main position, some experts who hook the sky have repeatedly won the championship, not to mention that traditional fishing is the mainstream in the complex environment in the wild, but there are still people who hook the sky.

Although the surface of kareem abdul-jabbar looks the same as most ordinary light hooks, except that an iron weight is welded on the tail of the hook, it has a very special place when it is used. The following are the specific features and methods.

1, the tin weight is proportional to the hook. If the hook wants to achieve the effect of flying upwards, it mainly depends on the weight of tin. If the tin is heavy and the hook is small, although the hook tip flies upwards, the fish can easily touch the tin when feeding. When lifting the pole, the hook is easy to slip from the fish's mouth, but if the hook is big, it will go to the DPRK.

2. The length of the hook handle should be moderate. The handle of the hook is too long, and the solder is not firm and easy to loosen and fall off. When the fish suck the hook, it is easy to cross in the mouth, and the fish will run away quickly after spitting it out. If the hook handle is short, the bait will be shallow and easy to unhook, so the authentic hook has a certain proportion. The upper layer of the tin weight is parallel to the hook handle, and the hook tip is perpendicular to the tin weight.

3. Check the tension of the hook. The hook will be heated for the third time during welding. Improper operation will affect the strength and toughness of the hook. The specific inspection method is to hold the tin weight in one hand and the hook in the other and pull it suddenly. If the hook is straight, it means that the hook quality is not good. If the hook is only slightly bent and then restored to its original state, it is a good quality hook, so choose a good quality hook.

4. Check the center of the borehole. After passing through the hole, the weight of the tin weights on the left and right sides of the wire body is equal. If it is not equal, it loses the meaning of hooking up with the sky. If it is less than 90- 100 degrees, the angle between the drilling hole and the hook handle should be checked, so that the hook line will be more evenly stressed and the fish will not be affected when eating the bait.

5. Pay attention to the balance between the hook and the buoy when configuring the kareem abdul-jabbar, so as not to affect the normal work of the fishing group and give full play to the sensitivity of kareem abdul-jabbar. Generally, the hook is mostly used for diving fishing, and the target fish is generally grass carp in crucian carp, carp, herring and miscellaneous fish. Therefore, the adjustment of the buoy is to make the bait just at the bottom of the water, and the buoy and the bait are in balance at the bottom of the water. At this time, the fishing group is the most sensitive and can

6, the correct use of deep-water hook fishing, the hook is generally used in the water depth of 0.5 meters to 2 meters, because the hook model is small, if fishing in deep water, the buoyancy of the water level may lead to endless situations, so at this time, it is generally possible to add lead to the hook to let the bait enter the bottom, and the distance between lead and the hook is generally between 3 and 5 cm, thus becoming hook fishing.

7. Check whether there is burr in the hole of tin weight, which is a very important and easily overlooked problem. If there are burrs in the hole, it is easy to scratch the fishing line. Therefore, under the condition of checking whether the hole is clear, thread the fishing line with a hose, then pass through the hose, and then pass through the groove on the hook handle, and tightly tie it to the welding place between the hook handle and the tin weight. This structure can effectively avoid the damage to the line caused by friction. However, after fishing, in order to prevent the line from being damaged by the fierce struggle of big fish, if there is any damage, the line can be pulled down about 10 cm, and the worn line can be cut and tied tightly.

It should be noted that if you catch a big fish, you should not only check the hook, but also use a fishing rod with excellent performance to ensure foolproof.