How to tie your shoelaces

How to tie your shoelaces to look good. There are 24 ways to tie shoelaces. Shoes are getting more and more beautiful, and shoelaces should be beautiful. How to tie your shoelaces to look good? Today, Bian Xiao of World Factory Textile and Clothing Network introduced 24 kinds of shoelaces. I hope friends can make your shoes look more beautiful by learning 24 ways to tie shoelaces.

Nowadays clothes and shoes are more beautiful and fashionable. Simple two shoelaces can actually be tied in many ways. Let's take a look at the 24 kinds of shoelaces that Bian Xiao brought to you today.

1, crossover method:

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. Cross the shoelaces and then pass through the other two holes respectively.

3. Repeat this process until the shoelace passes through the two holes above.

Evaluation: Is the traditional simplicity and comfort wrinkled?

Remarks: It is a comfortable tying method that everyone likes, mainly because the cross part of the shoelace is just in the groove between the upper on both sides, so it will not squeeze into the foot surface.

2, the upper and lower system method:

1. Thread the toe cap directly from the bottom (gray part) and out from the top of each shoe hole.

2. The toe cap passes through the bottom, through the second pair of shoe holes from bottom to top, then through the top, and then inserted into the third pair of shoe holes.

3. Repeat this process until the shoelace passes through the two holes above.

Evaluation: convenient decoration, less wear.

Remarks: If the shoe holes are odd pairs (7 pairs = 14 holes), the shoelaces should be threaded from bottom to top (gray part), so as to ensure that the shoelaces pass under the top pair of shoe holes.

3, direct method (European) method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. One end of the shoelace (yellow end) goes out obliquely from bottom to top and directly enters another shoe hole in the second horizontal row.

3. The other end of the shoelace (blue end) diagonally passes through the third row of shoe holes from bottom to top, and goes straight into another shoe hole.

4. Repeat the operation, and the two shoes lead alternately.

Evaluation: The short toe band has smooth surface and messy bottom.

Remarks: When the gap between the two sides of the upper that need to be tied together is too large, the mess of the lower part of the shoelace is obvious (as shown in the left picture). Although it looks messy, this cross can make the shoelaces tight and reassuring.

Suggestion: Military recommended direct method. On the one hand, it is safe, and on the other hand, when the foot is injured, the straight section of the shoelace can be quickly cut off with a knife or scissors, thus taking off the boots. However, it is said that the US military, which has strict rules on everything, made the following statement on their standard black leather combat boots: "The military boots should be obliquely tied with black shoelaces, and the extra-long part should be stuck in the top of the boots under the loose trouser legs or wrapped around the top of the boots." In this way, the straight tie law (European style) at least violates the regulations of the US military. It is suggested that military personnel use this method or other informal lacing methods for verification.

4, direct method (popular) method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. One end (yellow end) of the shoelace goes out from bottom to top along the right side and goes straight into another shoe hole in the second horizontal row.

3. Then pass both ends of the shoelace through a hole on the left.

4. Continue to thread both ends of shoelaces horizontally, and then thread them out in pairs again until one of them passes through the top hole.

5. The other end of the shoelace goes horizontally into the penultimate row of shoe holes, and then goes straight out of the uppermost shoe hole.

Evaluation: the most beautiful, slightly difficult, only applicable to even pairs of shoe holes (such as 6 pairs, 8 pairs).

Remarks: This method is only applicable to shoes with even holes, and there is a way to break through this restriction, as shown in the left figure (the top row of holes is blank). Here are several other solutions.