What are the steps for installing solid wood doors?

What is a solid wood door? Solid wood door This is a doorway made of wood, and solid wood doors can be divided into several types. Raw wood doors are common solid wood doors, but they are not the same. Solid wood doors also include wooden doors made of compressed wood boards. The installation of solid wooden doors is much simpler than the original wooden doors. Do you know how to install solid wood doors? The installation of solid wood doors can be carried out according to the tutorial. Next, let Bian Xiao share the installation tutorial of solid wood doors.

? Solid wood door installation tutorial

First,? Replacement tool

Electric hammer, carpenter's hammer, flat file, edge planer, fine tooth saw, screwdriver, spirit level, square, tape measure, hanging wire hammer, electric drill, hole opener, punch and drill bit with corresponding specifications.

Second,? erection material

60 nails, self-tapping screws (40, 25), wooden nails, small wooden strips, 502 glue, styrofoam glue, floor glue, door locks, door suction, hinges, wall moistureproof materials, towels.

Third,? Installation step

1, assemble the door cover

(1) combined door cover: adjust the width of the corresponding door cover according to the thickness of the wall, and fix the tapping plate and adjusting plate with 25mm tapping screws on the back of the door cover. The spacing between the screws should be no more than 250 mm, and the gap between the striking plate and the adjusting plate after combination should be less than 0.2 mm.

(2) Saw the top of the assembled vertical plate into the same plane and form a 90-degree angle with the vertical plate.

(3) Saw a gap at the top of the riser, and the position and size of the gap must conform to the specifications. The door stopper protruding from the top cover plate must have a straight cut, which should be polished smoothly with a flat file, and there should be no Mao Kou edge.

(4) combine the top plate of the door cover with the vertical plate, press the cover of the top plate on the vertical plate, insert the protruding door stop part of the top plate into the concave part of the vertical plate cutting saw, and fasten the two ends with three or four 40mm wood screws respectively. The openings should be in the same plane, the gap between the vertical cover and the top cover inside the door cover should be less than 0.2 mm, and the two vertical covers and the top cover must be at 90 degrees. Internal space size of door cover opening: width is door leaf width +7mm, height is door leaf height+13 mm. ..

2. Install the door cover

( 1)? Use an electric hammer to punch two rows of holes at a distance of 300mm (slightly inclined inward), and knock them in with a wooden needle of corresponding size to fill them.

(2) Put the firmly assembled door cover in the doorway, and roughly fix the periphery of the door cover with small wooden strips. Both sides of the door cover should be on the same plane as the wall, and then check whether the door cover is vertical to the ground and whether the two included angles between the top plate of the door cover and the two vertical plates are 90 degrees.

(3)? Use a speed-regulating electric drill (4.2mm drill bit) to guide holes in the door cover, and then fix the hinge of the door cover on the wall with 60mm nails, and then fix the other side of the door cover and the top cover plate after determining the opening size. The diagonal error between them should be less than 2 mm Because there is a gap between the door cover and the wall, it can be filled with small wooden strips and styrofoam at this time to make the connection between the door cover and the wall more solid and dense.

(4)? Stick a soundproof bumper on the door cover.

3. Install the door leaf lock

( 1)? When opening the hinge slot and unlocking the lock hole, be careful not to damage the top paint of the door and other parts of the door cover during the operation.

(2)? When installing the hinge, first screw a screw up and down the hinge, then close the door to check whether the gap is consistent and whether it is flexible to open, and then tighten other screws after confirmation. It is forbidden to screw the screws directly into the door sash and door cover.

(3)? Install the door lock. Install the door lock in the corresponding position. The height of the lock from the ground is generally 900-1000 mm. After installation, check whether the switch of the door leaf and door lock is flexible and whether the joint meets the specifications.

4. Install the door cover wire

Cut the door cover line of the right-angle edge into a 45-degree oblique angle, polish and trim it with a carpenter's plane, insert the right-angle edge into the door cover groove, and stick the door cover line to the door cover with floor glue.

5. Install the door suction in the corresponding position.

After reading the detailed process of solid wood door installation, the decoration owner can supervise whether the construction technology meets the specifications when installing solid wood doors, and no longer have to worry that the decoration layman will be perfunctory by the decoration company.

The above is the installation tutorial of solid wood door. Have you learned the installation method of solid wood door after reading it? The installation of solid wood doors is relatively simple, but it is also more complicated for some people who don't understand. Friends who don't understand the installation of solid wood doors, it is best to ask a professional carpenter to install it, because the professional carpenter's installation standard will be higher. Many people don't know that it takes ten inches to install wooden doors, and wooden doors with the wrong size will be staggered. Therefore, it is best to choose a reliable master to install solid wood doors.