Self Build House Plumbing Wiring Methods How are plumbing lines routed? Self-build house plumbing wiring way plumbing lines frequently asked questions

Self-built house plumbing wiring way plumbing line how to go?

1, into the wall concealed

Water pipe hidden in the wall, and can use artificial marble and other materials to decorate the exterior, so as to ensure the beauty of the bathroom, but also do not need to clean the pipeline, and not afraid it will be damaged. But can not ensure that the water pipe can be used for a long time, in the future if the water pipe is damaged if you need to remove the brick to repair, very troublesome.

2, open pipe installed

Take the open road exposed pipe will affect the bathroom's aesthetics, you guessed a line in the bathroom wall is not very beautiful, and exposed water pipe is easy to accumulate dust and stains, and not good care.

3, go to the top

This is the most difficult method of water pipe installation, and more material, but if the use of water leakage occurs, it is easy to find, will not cause major damage, and will not damage the ground waterproof. If you need to cross the hall, there will be a ceiling or plaster line to do cover, does not affect the beauty!

4, go to the ground

This installation method is the simplest, the material is not much, but the use of water leakage if it occurs, it is not easy to find. Maintenance is the most troublesome, but also may cause significant damage, such as soaking the floor, remove the tiles, and even affect the downstairs tenants of the ceiling, and the installation will destroy the waterproofing of the ground!

But generally workers prefer this installation method, because the construction is simple, and it is not they are responsible for later maintenance.

5, go to the wall

This installation method is more difficult, but the material is the least, the later occurrence of water leakage repair is also relatively easy, generally does not cause major damage, but in the construction of the slotting difficulties, will destroy a lot of walls, but will not affect the ground waterproofing!

What are the common problems of self-built house plumbing?

1, how deep to open the slot? Buy triangle valve, hose and so on how much should I buy?

A: General 3cm or so. Triangle valve and hose a bathroom and a kitchen with 6-8, two bathrooms and a kitchen with 8-12, specific in the installation of faucet to determine.

2, two brands of water pipes in the connection will have problems?

Answer: different brands of PPR pipe used in raw materials are different, heat fusion coefficient is not the same, the cooling time is different, so it is not recommended to do so.

Self-constructed house plumbing piping considerations

1, the waterway should be clear

Water pipes as the arteries of the living room, problems are also the most terrible part of the plumbing construction loopholes. Design should be considered in the security, reliability, should not be affected by external forces around the location and ease of maintenance and repair, at the same time, but also to follow the way, do not affect each other's principle, the water pipe design should be the upper water pipe and the lower water pipe separate do not cross the confusion. Therefore, a good design should be in strict accordance with industry norms.

2, hot water pipes and wires can not be too close

In order to avoid the safety hazards of plumbing construction, water and electricity are absolutely incompatible, so the waterways and circuits are by no means allowed at the same time are laid on the ground in the unlikely event of a problem will be extremely dangerous, the upstairs of the ground of the house will be downstairs at the top of the electrical appliances overlap and intersect. This can have serious consequences if anything goes wrong. In particular, the hot water pipe can not be too close to the wires, wire piping and hot water pipe have heat release, tightly connected, easy to heat deformation, thus causing short circuit.

3, water pipe buried pipe to be deeper

Water pipe construction, in order to be beautiful, are now generally buried in the wall, but if the buried is not deep enough, it will also lead to leakage and other problems, in general, the water pipe is buried -0.60m, through the ground with the bottom of the beam outside the row, buried shallow along the direction of the pipeline laying bricks high over the top of the pipe for 20 centimeters, the outside of the pipe cavity filled with sand on the top of the pipe paved with a 10-centimeter-thick band Reinforced cement board, and then backfill to the elevation.

4, the water pipe must be horizontal and vertical

Water pipe laying must be horizontal and vertical, so that subsequent workers in the construction of water pipes can grasp the direction of the pipeline to avoid puncture. In addition, before the construction must first check the ground there is no "line is strictly prohibited to hit the eye" and other signs line, so as not to break the underground pipeline. In addition, the construction should pay attention to the pipe to keep water, once broken in time to detect the problem; if the completion of the opening of the main valve only to find that the pipe is leaking, resulting in losses will be greater.