Installation skills of old-fashioned plastic steel window screen

How to install stainless steel wire mesh, how to install stainless steel wire mesh.

Step 1: Prepare material ① 1 screen: stainless steel wire mesh or invisible window screen; ② Two clips: to fix the height of the screen window; ③ Four triangles: used to fix the outer frame and pvc link; ④ Four strips: each strip contains the corresponding length (adhesive-backed magnetic strip, card slot magnetic strip and pvc plastic strip).

Step 2: after the tools are ready, we will determine the size of the window frame and cut off the excess pvc. After determining the size, insert the pvc strip into the triangle to make a frame.

Step 3: Lay stainless steel gauze flat on the finished frame, and press the gauze into pvc strips with slotted magnetic strips. It is suggested to tilt the slotted magnetic strip and push the gauze into the inside of pvc strip. Press the outside again.

Step 4: Then, cut off the extra gauze outside the frame along the frame to keep the overall beauty of the screen window.

Step 5: suck the adhesive-backed magnetic stripe on the magnetic stripe of the card slot, install a second clip at a position about 30% away from the top of the frame, pull the protective film of the adhesive-backed magnetic stripe at the position where the clip is installed, install the clip and install the screen window.

Step 6: Before installing the screen window, remind everyone to clean the window frame and keep it dry. First, tear off the protective film of the upper adhesive magnet. After fixing the position, gradually tear off the adhesive protective film on the left, right and lower ends and the clip, and press the adhesive magnetic strip hard.

Step 7: Install strings on the two triangles below, and open and close the screen window, thus installing the stainless steel screen window. It's convenient to take it off when not in use.

Precautions:

Do you know how to install stainless steel wire mesh? Also, after the screen window is installed, there is no problem. If you want to prolong the service life of the screen window, we must maintain it regularly when using it. The daily care of the screen window is very simple. Besides spraying lubricant on the track to keep the track lubricated, it is necessary to add some oil to the positioner.

Installation method of gorgeous basin for Overly 1 plastic steel window. Cut the installation opening diagram of the basin along the cutting line and check it with the actual size of the basin.

2. Copy the opening diagram on the marble countertop and trace the opening line to be cut on the marble countertop with a pen.

Note: Installation space for faucet installation of water supply pipe, drainage parts and inlet angle valve. Should be reserved under the marble platform.

3. After drawing the marble hole line, drill a hole in the cutting opening, then cut the table along the inner side of the drawn cutting line and smooth the cutting edge.

4. Install marble countertops.

5. Put the basin into the cutting hole of the marble countertop, correct the position, and draw an outline on the countertop along the outer edge of the basin with a pencil.

6. Remove the basin and install the faucet and water as required.

7. Wipe the glass glue evenly on the table between the edge line and the cutting edge of the basin.

8. Install the basin on the countertop and check whether its position is accurate. Then flatten the basin and wipe off the excess glass glue at the edge of the basin.

9. After the glass glue is dried, connect the water inlet connector and the drainage connector. When connecting the water inlet pipe fittings, drain the water in the pipe for 3~5 minutes to clean the pipe and prevent the sand in the pipe from blocking the angle valve and faucet outlet.

10, turn on the tap and check whether the interface leaks.

Tips for purchasing plastic steel windows in Fujian-Xiamen bathroom basin Yang Fei Giant 1. The first thing to observe the profile quality is the profile appearance, and the color should be bluish white, not white as people usually think. Pay attention to whether the profiles of frames and fans that make up doors and windows are consistent in color, uniform in appearance and reasonable in cavity distribution.

Calcium carbonate is usually added to the profile of plastic-steel window as filler, but in order to reduce the cost, some manufacturers will become calcified plastic if they add too much calcium. The surface of doors and windows made of this plastic is dull, slightly rough, hard and brittle, and looks rough like a stone. Ordinary plastic steel windows usually have shiny and tough surfaces.

2, gap and seal to see whether the fit gap between various profiles is tight, whether the cut at the fit is flush, the height difference of profile lap, and so on.

Generally speaking, for plastic-steel doors, the main parts to be considered are the gap between the door frame and the fan, the door panel layering and the door panel edge, the joints of various profiles of shutters, sealing strips and so on. In the case of assembling door panels, the gap between door panels should also be considered; Whether it is a horizontal door depends on whether the two doors are transparent after closing.

In addition to the assembly clearance of various profiles, it is also important to consider whether the sealing strip is uniform and firm, and the interface clearance should not be greater than 1mm, which reflects the sealing performance of the window.

If it is a plastic steel door with an inner door, the requirements are not so strict.

National standards stipulate various gap values, but for customers, the smaller the gap value at the joint of various profiles, the closer the fit, and the more exquisite the technology, which reflects the accuracy of the level and tools.

3, welding to see whether the weld is flush, crack, Yin and Yang Angle joint is clean and beautiful. Measure the diagonal dimension of the plastic-steel window with a box ruler. The diagonal dimension difference should be no more than 3 mm The smaller the diagonal dimension difference, the finer the display technology and the more favorable the installation.

4. The quality of hardware also has a certain influence on the life of doors and windows. The hardware used should look thick, with good surface gloss, dense protective layer and no scratches. The most important thing is to be flexible and open.

5. Steel bars have different requirements for wind pressure resistance of plastic-steel windows according to national standards. The inner cavity of the sash of the plastic steel window needs to be assembled with steel bars. According to different heights, there are three kinds of reinforcing ribs with thicknesses of 1.2mm, 1.5mm and 2.0mm to ensure the firmness and service life of products.

Some manufacturers do not install or install unqualified steel bars in order to reduce costs.

Customers should pay special attention when buying products. Usually, the inspection methods are:

1. Estimated by the weight method, that is, when the doors and windows are weighed, the door and window components with steel bars are heavy, and vice versa.

2. Put magnets on door frames and door sashes. If the magnet is attracted, there will be reinforcement inside the profile, otherwise there will be no reinforcement.

3. Observe whether there are screws for fastening section steel on door and window frames and fans, which can also prove whether there are reinforced section steel.