Wall manual drilling of tile drilling precautions drilling steps are all what

Decoration is a technical work, a lot of processes, the average person if they do not know the method and know-how, there will be a lot of problems. For example, bathroom wall drilling, we have found that the bathroom wall are tiles, drilling is easy to cause tile breakage, very much affecting the aesthetics, we bring you manual drilling of the wall of the tile drilling precautions? Tile drilling steps are what?

A, wall manual drilling of tile drilling precautions?

1, wall manual drilling of tile drilling precautions - drilling location

Punching location is best to choose the joints of the two tiles, if not suitable, can be in the middle of the tiles, can not be selected on the edge of a piece of tile, so it is easy to make the brick body rupture.

Punching holes before checking whether the tiles at the drum, if the drum needs to be re-selected location, because the drum at the hole is very easy to lead to broken tiles fall off. In addition, pay attention to the corresponding position in the wall, avoiding beams and columns, utility lines.

After determining the location, mark it with a grease pencil or pencil.

2, wall manual drilling of tile drilling notes - choose the right tool

Drilling may use impact drills, pistol drills, hammers, and the corresponding drill bit, choose which, how to use, there are instructions.

General opinion, tile drilling drill best not to use concrete drill, you should use tile special drill, glass drill (reportedly building materials market a 5 yuan can be purchased).

The drill bit is best to use hollow tubular diamond open hole drill bit, followed by like a bow and arrow head of the tile open hole drill bit. There are arrow-shaped bits for tile-specific drilling on the market today, which are much easier and faster.

3, wall manual drilling of tile drilling notes - control the size of the brick hole

When using a glass drill bit to drill holes in the tiles, first tilt the direction of a small pit to hit. If you want to be precise, you can use a board (tile bar) that already has a hole (the right size) to set the positioning, and you can remove it after making a shallow mark, and then proceed to punch the hole to be punched through. But remember: this hole must be 1.5-2mm larger than the actual hole to be used.

If you are playing a large-diameter hole (such as smoke holes), you can use a drill to turn a round impression mark on the tiles first, and use a tile drill to drill another circle of holes around the impression mark and then go on the drill, which makes it easier to operate.

4, wall manual drilling of tile drilling precautions - continuous watering

Drilling process to add water to cool, otherwise the drill bit is easy to burn off. The operation is as follows:

Find a mineral water bottle → full of water → cap tie a hole → watering while drilling → to the drill and tile contact parts of the water (especially the full tile, be sure to water).

5, wall manual drilling of tile drilling precautions - drilling force to be balanced

Punching operations, do not exert too much force, and do not rock the drill left and right.

6, wall manual drilling of tile drilling precautions - drill clogging to unclog

Each play a good hole, to remove the drill bit, the clogging of the hollow part of the drill bit to unclog a bit, deal with the full tile especially to do this step.

7, wall manual drilling of tile drilling notes - heavy bolts to be long enough

Rise plug (plastic expansion tube) plugged into the punched holes, is considered to be a great success. Some masters say, if the tile installation of heavy-duty bolts, you must choose than the original bolt 3 centimeters longer than the bolt, otherwise it is very dangerous.

8, wall manual drilling of tile drilling notes - electricity safety to be careful

When using the drill, wear insulated gloves.

Two, tile drilling steps are what?

1, first you need to check the location of the utility lines that you photographed and left, do not accidentally drill into the wires and pipes. Then mark the place where you need to drill with a pencil and tape it.

2, find a sample punch or steel nails, pay attention to not use iron nails Oh, and then use the hammer and sample punch in the marked place to drill a small hole, so that the back of the hand will be a little more stable, to avoid the drill bit touching the glaze on the surface of the ceramic tile after slippage. Do not worry about drilling through the adhesive tape.

3, to the impact drill loaded with impact hammer, vertical alignment of the previously drilled point, the beginning of the force is not too big, such as penetrating the tile and then use a little force to play a little deeper.

4, after the hole is good, you can install the expansion pipe, and then you want to install the shelf what are installed on the fixed line.

While according to the above approach to the success rate is relatively high, but the tile is more brittle or cracked, here to provide three tips:

1, in the tile at the intersection of the hole is better, not easy to crack, that is, is the middle of the two pieces of the center of the joints, as well as the center of the four pieces.

2, tile drumming is normal, 5% within the are no problem, but pay attention to can not drill holes in the place of drumming, 100% crack ah.

3, wall tiles are more absorbent, you can drill holes in the constant spraying of water, so that the nature of the tiles stabilized will not be easy to crack.

Above about the wall manual drilling of tile drilling notes? Tile drilling steps are what? The precautions of the whole knowledge is introduced to you here, because in the process of renovation, is not to avoid drilling, so if you are worried about their own not professional enough, then we can ask a professional to help punch, do not easily go to the hole Oh, or there will be very serious consequences.