Lifan maiwei fault code daquan

The fault code at the beginning of the fault description is P0AA4. The negative contactor circuit of hybrid battery is stuck in the off position P076F 7. The transmission ratio is incorrect. P0B2B hybrid battery C voltage P0A3E generator converter temperature is too high. P0 126 The coolant does not reach the stable working temperature P0B 1E hybrid battery voltage monitoring. D circuit P0AF3 Drive motor inverter temperature sensor B circuit range/performance P06 1B Internal control module-torque calculation performance P0929 Shift lock solenoid valve/actuator control circuit A/ range/performance P0 154 Oxygen sensor circuit has no effect (row 2, sensor 1) View all the results. The fault code P 1 starts with the fault description P 1825 transmission gear switch. Signals A/B/C and P- signals are incorrect. P 1233 Fuel pump drive module is disabled or disconnected. P 15A7 Oil pressure-too low before starting. P 1580 Throttle actuator control monitor-fault P 100B variable valve timing system-slow response (2nd row). P/ 603 Transmission Control Module -EEPROM Fault P 1532 Idle Control-Low Mixing Ratio Running Speed Below Set Value P 6538 Diagnostic Detection Communication Line-Fault P 1294 Idle Air Control System-Incorrect view of all results at idle speed Fault code P2 starts from fault description P2000 NOx trap efficiency below threshold (line 1 line) P2/ Kloc-0/2 1 Throttle/accelerator pedal position sensor/switch D circuit range/performance P226A Water in fuel indicator control circuit P20A9 reductant injection air pressure control valve high P2549 torque management request input signal B range/performance P252D oil quality P257D engine cover switch circuit range/performance P2064 reductant/regeneration supply control circuit high P25/ Kloc-0/8 air conditioning refrigerant pressure sensor B circuit high view all results Fault code P3 starts fault description P346 1 cylinder 8 exhaust valve control-circuit open P3470 cylinder 9 exhaust valve control-performance problem P34 15 cylinder 2 exhaust valve control-circuit low P346. 0 cylinder 8 cylinder deactivation system/intake valve control-circuit high P3429 cylinder 4 exhaust valve control-circuit open P3405 cylinder 1 exhaust valve control-circuit open P3428 cylinder 4 cylinder deactivation system/intake valve control-circuit high P3443 heated oxygen sensor 3- no activity detected P3409 cylinder 2 cylinder deactivation system/intake valve control-circuit open p34/kloc-0. Intake valve control-performance problems View all results. Fault code B starts with fault description B0002. Before the driver (a B2293 restraint system-airbag fault B00A 1 occupant position system (sub-error) B00CB passenger seat occupant position sensor E (sub-error) B009 1 left restraint sensor 1 (sub-error). B009C Left Restraint Sensor 6 (sub-error) B0020 Left Airbag Deployment Control (sub-error) B00D 1 Passenger Seat Belt Indicator (sub-error) B0073 Second Row Left Seat Belt Pretensioner-Start Control (sub-error) Fault code U begins with a fault description. U0204 lost communication with door control module F. U0548 received invalid data from the seat control module F. U0422 received invalid data from the body control module U0 1 19. Lost communication with fuel cell control module U040D. U040D from turbo/supercharger control module A received invalid data. U047F received invalid data from seat belt tensioner module a. U0 133 lost communication with the active roll control module U0228. Lost communication with window motor (sub-error) C0069 Yaw rate/longitude sensor (sub-error) C002 1 Brake booster performance (sub-error) C 1 4 Incorrect module design level (incorrect applicable vehicle type) C0075 Brake pedal stroke is extended and output to powertrain control module (sub-error)