Traditional Culture Encyclopedia - The 24 Solar Terms - Dongfeng Shen Feng AX3 Fault Code Collection

Dongfeng Shen Feng AX3 Fault Code Collection

Fault description at the beginning of fault code P0 P0 193 Fuel rail pressure sensor A circuit high P00B6 (water tank) radiator coolant temperature/engine coolant temperature correlation P0803 upshift (jumper) solenoid valve control circuit P07 12 Transmission oil temperature sensor A circuit low P0A5A generator current sensor circuit range/performance P096 1 Pressure control solenoid valve A control circuit range/performance P06B0 sensor power supply A circuit/open circuit P0C32 hybrid battery cooling system performance P0262 fault description at the beginning of fault code P 1 P 1644 throttle adaptive-mechanical stop unsuitable (line 1 line) P 1356 ignition coil/amplifier, Cylinder 1- short circuit to positive pole P 1505 idle air control (IAC) valve-open signal P 1560 engine control module (ECM)- battery power supply voltage P 1449 catalytic converter temperature sensor b-range/performance P 1 7449. 509 Idle Air Control (IAC) Valve-Engine High Speed P 1490 Engine Coolant Fan Motor Relay-Low Speed/Circuit Fault P 1 125 Throttle Motor Position Sensor, A/B-Small Range/Performance Problems View all results. The fault code P2 starts from the fault description P2706 shift solenoid valve P2425 exhaust gas recirculation system cooling valve control circuit/circuit breaker P2258 A circuit controlled by secondary air injection system is high P2094 B (exhaust/right/rear) camshaft position actuator control circuit is low (2nd row). P2753 transmission oil cooler control circuit/circuit breaker P2683 engine coolant bypass valve control circuit high P2803 transmission gear sensor B circuit high (PRNDL input) P2686 actuator power supply voltage C circuit high P2402 fuel evaporative emission system leak detection pump control circuit high P2099 rear catalytic converter fuel regulation system (mixture ratio) is too rich (second row). View all results. Fault description at the beginning of fault code P3 p 3429 4-cylinder exhaust valve control-open circuit P3492 12 cylinder shutdown system/intake valve control-circuit height P3450 cylinder 7-cylinder shutdown system/intake valve control-performance problems P3497 cylinder shutdown system (second row) P34 1 6 cylinders and 2 exhaust valve control-circuit high P3446 cylinders and 6 exhaust valve control-performance problems P3438 cylinders and 5 exhaust valve control-performance problems P3466 cylinders and 9 cylinders cylinder deactivation system/intake valve control intake valve control-circuit high P3495 cylinders 12 exhaust valve control-circuit low view all results fault code b Start fault description B00E3 second row left seat belt pretensioner c Start control (sub-error) B2477. B00B8 Driver's seat occupant position sensor B (sub-error) B0020 Left airbag deployment control (sub-error) B0088 Third row right seat belt load limiter-start control (sub-error) B2434 Driver's seat belt buckle switch circuit short circuit to ground B004A Third row right front (airbag) Second stage deployment control (sub-error). B007B Row 2 Left Seat Belt Pretensioner B Start Control (Sub-error) B 13 17 Battery voltage is too high View all results Fault code U Start fault description U0499 Received invalid data from telematics control module U0030 vehicle communication bus A(+). Open circuit U0409 receives invalid data from alternative fuel control module U0330. Tire pressure monitoring module software is incompatible U0599 receives invalid data from DC-DC converter control module A. U0033 Vehicle communication bus A(-) Open circuit U0565 receives invalid data from camera module (rear) U0042 Vehicle communication bus B(-). Open circuit U040B receives invalid data from exhaust gas recirculation control module A U0035 vehicle communication bus A(-). Check all the result fault codes C to describe the fault C0002 driving anti-skid traction control (TCS) system (TCS) control channel A valve 2 (sub-error) C0040 brake pedal switch A (sub-error). C0037 Left rear wheel speed sensor (sub-error) C0075 Brake pedal stroke is extended and output to powertrain control module (PCM) (sub-error) C00 1D Right rear exit control (sub-error) C 14 14 Incorrect module design level (not applicable to the correct model) C0084 Roll.