? Detailed explanation of installation steps of shower head Detailed explanation of seven points for attention in installation of shower head

Shower shows us a different way of life, which is the continuation of its functionality. Many big brands are developing various models of shower heads. In addition to the basic universal water flow for simple and quick shower, there are different water flow and water quantity controls for additional functions, such as * * *, shampoo, etc. In this way, you can make every bath very comfortable. Next, I will tell you about the installation steps and precautions of the shower, and see if the shower is installed well.

Detailed explanation of installation steps of shower head

Shower installation step 1: wind the raw material belt around two elbows, and then screw it on the water outlet connectors of two installation holes on the wall with adjustable wrench. After fastening, ensure that the center distance between the two elbow joints is150 mm.

Step 2, installing a shower head, and sleeving two decorative sleeves at the elbow;

Step 3: Install the shower nozzle. Insert the mounting washer into the elbow joint, tighten the mounting nut on the elbow joint with a wrench, and fix the faucet on the wall.

Step 4: Install the shower nozzle. Drill three holes with a diameter of 6mm and a depth of 35mm at a position about "H" from the faucet outlet joint.

Step 5: Install the shower nozzle. Drive the expansion pipes into the installation holes respectively, and fix the wall seat on the wall with self-tapping screws. Note: the wall seat must be on the same center line with the faucet outlet connector.

Step 6: Install the shower nozzle. Wrap the faucet with cloth before drilling to prevent the faucet from being dirty and bruised.

Shower installation step 7. The height "h" should be determined in the actual installation process according to the actual product.

Shower installation Step 8: Insert the sealing ring into the lower end of the switch valve.

Step 9: Install the shower head: Tighten the lower end of the on-off valve and the upper end of the faucet through threads.

Shower installation steps 10. Before drilling, wrap the faucet with cloth to prevent it from being dirty and bruised. Note: When tightening with a wrench, be careful not to damage the electroplated surface.

Shower installation steps 1 1: screw one end of the shower rod and one end of the on-off valve by thread (the end of the column shower rod must be equipped with a sealing ring).

Shower installation step 12: then put the decorative cover into the other end of the shower rod, then insert that end into the wall seat, lock that end with three fastening screws respectively, and finally push the decorative cover onto the wall;

Shower installation steps 13. After installation, turn on the water inlet switch and thoroughly flush the pipeline.

Shower installation step 14: connect the nut end of the shower hose with the connector behind the switch valve body, and insert the nut into the shower seat after connecting with the end of the hand-held shower (note: there must be washers at both ends of the shower hose.

Shower installation steps 15: Screw the top nozzle onto the shower panel.

Detailed explanation of seven points for attention in nozzle installation

Seven points for attention in installation of shower 1, height of mixing valve from the ground

The inner elbow is reserved for the shower head to prepare for the installation of the water mixing valve in the next step. Its height is generally between 90- 1 10cm, which can be determined according to the owner's requirements or the average height of husband and wife. It can't be higher than 1 10cm, otherwise it can't install a shower with a lifting rod, and it can't be lower than 90cm.

Seven points for attention in shower installation II. The spacing between two internal threads.

Experienced plumbers all know that the reserved spacing standard of elbow in shower is concealed installation 15cm, with an error less than 5mm and exposed installation 10cm. Remember that everything is centered and measured. If it is too wide or too narrow, it is not appropriate. Don't rely on adjusting alignment. The adjustment range of alignment is very limited.

7 points for attention in installing shower 3. Keep a plane with the wall after pasting the wall brick.

The thread ends are reserved in consideration of the thickness of wall tiles, and it is better to make them 15mm higher than the blank wall. If it is flush with the blank wall, you will find that the thread is too deep in the wall after pasting the wall tiles, and maybe the shower will not fit. However, you dare not stay too high from the wall. If it is too high, the thread ends and adjusting screws will not be covered in the future decoration, which is very ugly.

7 Precautions for installing shower. Pay attention to different styles of showers.

Nowadays, with the continuous improvement of people's quality of life, shower styles are varied, and the installation methods are also different, such as surface installation, concealed installation, wall hanging and ceiling installation. As a hydropower worker, we should constantly learn and master the installation methods of new products in the market.

7 Precautions for installing shower. Site selection is very important.

Shower is a bathing device, and people have to wear clothes when taking a shower, so we should pay attention to its privacy when installing shower. Generally don't choose at the door or by the window. In addition, if there is an integral bathroom, it is necessary to fully communicate with the owner about the size of the purchased integral bathroom and see where the shower mixing valve is left. Never wait until it is decorated. After the bathroom is bought back, if the left position is not suitable, it will hit the wall.

Shower 6 installation attention at seven o'clock. It can't be wrong to be warm left and cold right.

There is nothing wrong with the left-hand heating and right-hand cooling of the elbow outlet of the shower. This is not only the national standard, but also the usage habit of the majority of owners. More importantly, the products of the manufacturers are also produced according to the regulations of left-hand heating and right-hand cooling. If you make a mistake, some equipment may not work or damage the equipment. This point should be paid attention to when laying pipelines.

7 Precautions for installation of shower 7. Internal elbow fixation

It is very important to fix the inner conductor elbow. If it is not fixed, the size can not be positioned, and the mixed-flow valve may not be installed after the transformation.

Well, my introduction to the installation of shower ends here today, I hope it will help you! Want to know more about the installation of shower, please continue to pay attention to our website!