How to install pvc ceiling bath bar what type of bath bar is good

I believe that when you are decorating a room, you need not only many decorative materials, but also many household appliances to make a complete decoration of the room. Especially when decorating the bathroom, because when decorating the bathroom, not only do you need a water heater, but you also need a bath bomb that can heat up the room. This will allow people to take a bath without catching a cold because of the sudden coldness of the air. The following is a small introduction to the installation of pvc bath heater ceiling, to facilitate the installation of pvc ceiling bath heater in the bathroom.

pvc ceiling bath bar installation method

pvc ceiling bath bar installation preparation

1, equipped with tools

drill, adjustable-speed hammer, cutter or grinder;. Right-angle ruler, tape measure, level; multimeter, utility knife, wire cutters.

2, spare materials

Steel nails, common nails, wood screws; insulating tape, gloves; wood.

3, measurement

Confirm the accurate installation dimensions; the specific size and location of the house and various structures; the installation height of the ceiling; the installation location of the host and the direction of the determination; the template with the program and the confirmation of the host.

pvc ceiling bath bar installation steps

1, the installation of the edge line

Collector strip installation should be flat, firm, determine the installation height, and draw a horizontal line. After a good pasting of tiles, horizontal, the matching edge line of the integrated ceiling, tightly fixed on the tiles, to do without obvious gaps.

2, keel installation

Under the boom and racking light steel keel, boom, the distance between the keel to do and panel size. At the top of the expansion eye and fixed all the boom, the lower mouth of the boom and hook connection, and then the main keel frame in the middle of the hook and fixed, adjust the height of the nut so that the bottom plane of the main keel from the edge of the bar on the plane line 3cm and fastened.

3, pay the keel installation

According to the actual installation length minus 5mm to intercept the required pay the keel, set of triangular pendant, according to the drawing requirements of all the pay the keel with a triangular pendant temporarily attached to the main keel.

4, buckle plate installation

Wear clean gloves, the installation of buckle plate to consider the overall aesthetics and symmetry of the two sides. Cutting method: the template is fixed, with a hobby knife and ruler engraved more than three times, the folded edge with scissors cut into 90-degree angle, folding pressure by hand 2-3 times can be. The corresponding face of the template cutting mouth is stuck in the pay keel, the face of the cutting mouth is erected on the edge strip, and pull out the edge strip card position to tighten the template, at this time, the triangular lifting piece can be tightened with the steel pincers and the main keel card. When installing the middle part of the template, the two corresponding sides of the template are stuck in the payment keel, and the gap between the templates is controlled to keep the splicing seam straight. Note: After completing the installation of each row of templates, the triangular lifting member should be tightened with steel pliers and the main keel.

pvc ceiling bathtub installation method

pvc ceiling bathtub installation preparation

1, equipped with tools

drill, adjustable-speed hammer, cutter or grinder;. Right-angle ruler, tape measure, level; multimeter, utility knife, wire cutters.

2, spare materials

Steel nails, common nails, wood screws; insulating tape, gloves; wood.

3, measurement

Confirm the accurate installation dimensions; the specific size and location of the house and various structures; the installation height of the ceiling; the installation location and direction of the host to determine; the template with the program and the host to confirm.

p?vc ceiling bath bar installation steps

1, the installation of the edge line

Collector strip installation should be flat, firm, determine the installation height, and draw a horizontal line. After a good pasting of tiles, horizontal, the matching edge line of the integrated ceiling, tightly fixed on the tiles, to do without obvious gaps.

2, keel installation

Under the boom and racking light steel keel, boom, the distance between the keel to do and panel size. At the top of the expansion eye and fixed all the boom, the lower mouth of the boom and hook connection, and then the main keel frame in the middle of the hook and fixed, adjust the height of the nut so that the bottom plane of the main keel from the edge of the bar on the plane line 3cm and fastened.

3, pay the keel installation

According to the actual installation length minus 5mm to intercept the required pay the keel, set of triangular pendant, according to the drawing requirements of all the pay the keel with a triangular pendant temporarily attached to the main keel.

4, buckle plate installation

Wear clean gloves, the installation of buckle plate to consider the overall aesthetics and symmetry of the two sides. Cutting method: the template is fixed, with a hobby knife and ruler engraved more than three times, the folded edge with scissors cut into 90-degree angle, folding pressure by hand 2-3 times can be. The corresponding face of the template cutting mouth is stuck in the pay keel, the face of the cutting mouth is erected on the edge strip, and pull out the edge strip card position to tighten the template, at this time, the triangular lifting piece can be tightened with the steel pincers and the main keel card. When installing the middle part of the template, the two corresponding sides of the template are stuck in the payment keel, and the gap between the templates is controlled to keep the splicing seam straight. Note: After completing the installation of each row of templates, the triangular lifting member should be tightened with steel pliers and the main keel.

What type of bath heater

What type of bath heater

The four-in-one circulating heating bath heater

The four-in-one circulating heating bath heater is a set of heating, lighting, ventilation, blowing in one, the heating power with the room temperature, high thermal efficiency. High thermal efficiency. In the process of using, the indoor air to form convection, circulation heating.

What type of bath heater is good - negative ion purification bath heater

Negative ion purification bath heater in the process of heating, but also play a role in purifying the indoor air. This is a wind heating, light heating, lighting, ventilation, blowing, negative ion multi-function bath heater, which uses a needle resistance wire as the heat source, heating fast.

What type of bath heater is good - three-in-one affordable bath heater

Three-in-one affordable bath heater is a set of warming, lighting, ventilation in one, generally two or three lamps, inexpensive and more practical, heating and ventilation effect is ideal. In addition, the bath heater has the latest double protection, safer to use.

What type of bath heater - intelligent automatic five-in-one bath heater

Intelligent automatic five-in-one bath heater is a set of warming, lighting, ventilation, blowing, wind in one, built-in electric overheating protector, up to a certain amount of heat can be automatically shut down. This bath heater adopts the first double ultra-thin design, the thickness of the panel, the thickness of the box than the general bath heater reduced by 40%, beautiful and generous, and more compatible with the decoration.

What type of bath heater is good - infrared broadband radiation bath heater

Infrared broadband radiation bath heater with special treatment of infrared emission elements, can emit a wide spectrum of infrared radiation, can quickly activate the human body cells, clean and comfortable after the bath. This bath heater, using a special four broad-spectrum hard quartz infrared heating lamps, without preheating, just press the strong, weak two-step control switch, instantly make the bathroom temperature up to 25 degrees Celsius, but also with a waterproof remote control, you can adjust the temperature at will.

What type of bath bomb is good - carbon fiber bath bomb

Carbon fiber bath bomb will extend the service life to more than 8,000 hours, the carbon fiber heat sensing tube at high temperature does not oxidize, the resistance does not increase, not due to overloading of the current burned off, and strong aging resistance. Carbon fiber bath heater unique carbon fiber heat sensing tube, high thermal conversion efficiency, energy saving of more than 30% than the general metal heaters, fully realize the energy saving and environmental protection.

The above is a small introduction to the p?vc ceiling bath heater installation method, I believe that we should have a lot of understanding of the installation method of the ceiling bath heater after reading. When you choose the ceiling bath heater can choose in some big brands, because the big brands of the ceiling bath heater, not only good quality, and after-sales service to do especially perfect. If you have some quality problems in the process of use, you can contact the after-sales service for repair or replacement, I hope that my suggestions can help you.

Tubapu online free for everyone to provide "each decoration offer, 1-4 local decoration company, 3 sets of decoration design program", and decoration to avoid pit strategy! Click on this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, you can get it for free Oh~