What is a three-dimensional flowerpot? What kinds of three-dimensional flowerpots are there?

Three-dimensional flowerpots are loved by many flower lovers. It broke the traditional flowerpot style and adopted a three-dimensional and polygonal design, which made the original rigid flowerpot colorful and played a strong decorative role. Next, today I will introduce the types of three-dimensional flowerpots and the production process of three-dimensional flowerpots. Let's continue to look down with Bian Xiao.

First, the basic introduction of three-dimensional flowerpot

The three-dimensional flowerpot is a groove located at the bottom of the flowerpot. The two grooves of the flowerpot can be embedded in the two edges of the flowerpot, so that they can be stacked to form a flower wall, and then the ring can be folded. Diamond, triangle and other flower walls.

2. What kinds of three-dimensional flowerpots are there?

1. A three-dimensional flower bonsai household product, the main body is a cylinder (or three legs), and its spatial structure is divided into upper, middle and lower layers, each layer has three horizontal angles, which are separated by 120. Place the flowerpot stabilizer ring and flowerpot tray. Put the flowerpot on the tray under the stabilizing ring, and all accessories are connected by bolts. The necessary technical features are: after landing, it is necessary to lift three feet under the three-dimensional flowerpot frame, put a large flowerpot on the inclined "toe" tray, and press down the main body of the frame to lower its center, thus stabilizing the frame.

2. The second three-dimensional flowerpot has a cylindrical or tripod-shaped body. Spatial connection structure is divided into upper layer, middle layer and lower layer. Each floor has three sets of corresponding flowerpot stabilizing rings and flowerpot trays. Put it in the tray under the stabilizing ring. Its technical characteristics are: after landing, it is necessary to lift the three-dimensional flowerpot frame three feet, put the big flowerpot on the raised "toe" plate and press it on the frame to lower the center of gravity and achieve the purpose of stabilizing the frame.

Third, the method of self-made three-dimensional flowerpot

1. material preparation

PS tube: PS tube with a diameter of 40 cm -60 cm and a length of about 15 cm shall be purchased as required. It is heavy after overload, difficult to move and easy to be damaged. Elbow: 16 90-degree elbow, with a diameter of 50mm (4 bases, 4 flowers on each floor, 3 floors 16). Straight pipe: 2.5 meters, cut into 8 cm long with a hand saw, handed over with an elbow, and one end inserted into the 50 cm hole of the big pipe.

2. Tools used

Hand drill, hole drill (diameter 50mm), hand saw, hot melt gun, hot melt rod.

3. Specific production steps

Mark the punching position on the vertical pipe. The bottom layer must be a cross-shaped hole to facilitate the installation of four elbows on the ground and stabilize the upright position of the flowerpot. According to the requirements, the other layers can be cross-shaped or 120 degrees. There are many cross holes, and the cultivated flowers are beautiful. The distribution of 120 degrees is more concise. The holes in two adjacent layers are staggered by 45 degrees (or moderately), one layer is convenient for watering and other treatment, and the other layer is used for flower growth and beauty.

Open all holes at once. Each elbow is equipped with an 8 cm long straight pipe, one end of which is inserted into the elbow and the other end is inserted into the riser. Except the lowest elbow, such as the foot, everything is upward.

After fixing the elbow, insert the hot melt stick into the hot melt gun from the back, and then turn on the power. After heating for a few minutes, pull the trigger continuously and apply sol on the interface between each elbow and riser. After the sol is cured, it can play a role in fixing, waterproofing and leakage prevention.

The decorative effect of the three-dimensional flowerpot is really great. Whether at home or in the office, it is a beautiful and eye-catching landscape. I believe that everyone has a certain understanding of the types of three-dimensional flowerpots and the production process of three-dimensional flowerpots, hoping to help everyone.