How to connect the speaker connector

One, active speakers connected to the computer:

Active speakers connected to the computer is very simple, you through a 3.5m one-point-two audio cable, generally plugged into the computer's headphone output interface, the other side of the speaker plugged into the red and white interfaces, connected to a good power supply can work, and now go to buy a number of computer-specific speakers can be directly have a built-in amplifier. Plug and play.

Two, passive speakers connected to the computer:

1, and we focus on passive speakers connected to the computer, may be some of the lines and interfaces do not match, you need to be wired through welding. In the electronic market to buy a 3.5 to 6.5 stereo adapter cable, the jack is a 3.5mm plug, will be this plug line and speaker wire welding.

2, to put it simply is a 6.5 plug into the amplifier on a channel such as AUXDVD, etc. 3.5 plug into the sound card signal output on the OK. But many people are not good at welding lines, so they are afraid to weld themselves, first of all, they first test the polarity of the two lines of the speaker, the polarity of the reverse will be no sound.

3, with a No. 5 battery, the speaker's two lines were connected to the battery positive and negative poles, if the toggle line can be heard inside the speaker, "crackling" sound, then the negative battery connected to the ground, and vice versa, there should be no sound.

4, if the left speaker, is the left channel; if the right speaker, is the right channel. But if it is a digital connection only need a line on the line, one end of the sound card into the SDIF output of the other end into the SDIF input of the amplifier on the line on the sound quality is better.

Three, after testing the polarity of the speaker, stereo plug inside the three poles, respectively, is the ground and the left and right channels, the left and right speakers of the ground wire uniformly welded to the ground line of the plug, another wire welded to the left and right channels. There is also a plug shell that can be screwed on. Once soldered, and the plug shell covered, it's pretty much the same as a headphone head that you can buy out there.

Four, in fact, to put it bluntly, passive speakers connected to the computer is an amplifier amplifier connected to the computer on a process

Methods/Steps:

1. We see that the audio equipment comes with two sockets, one is the USB plug, and one is a metal plug.

2. We now find the back of the host, there are three round sockets, including the center of the tender green jack is the audio output jack.

3. We now put the round plug, inserted in the center round socket.

4. In addition to the USB plug in the host behind any USB port.

5. Now we go back to the front of the monitor, you will see a prompt to select the type of input device, we choose the front speakers, click OK.

How to connect the audio connector?

How to connect the audio connector cable of the stereo.

This way to connect: two bare wires (male **** ground) together with the longest one, the rest of the left and right channels of the main line were connected to the other two (listening is not natural can be adjusted,)

How to connect the audio link interface is what the junction port

Audio link interface is the input interface, there are two interface modes, a. Large audio is RCA socket. b. Micro audio is 3.5 mm. c. Micro audio is 3.5 mm. d. Micro audio is 3.5 mm. e. Micro audio is 3.5 mm. f. Micro audio is 3.5 mm. g. Audio is 3.5 mm. .Micro audio is 3.5MM socket. Can be connected in this way:

1. RCA socket, it is connected with a lotus plug. The other end to see what the audio source is the device, is a computer loss, generally 3.5mm dual audio plug, inserted into the green jack of the computer sound card can be connected, the connection line must be selected at one end is a Lotus head, the other end is a 3.5mm plug audio cable. DVD/VCD output, choose both ends of the audio cable is a lotus plug, inserted into the DVD\VCD RCA output socket can be.

2. The 3.5mm jack of the miniature stereo, use one end of the 3.5mm plug, the other end is a lotus head, can be connected to the DVD/VCD output. If it is connected to a computer, use a cable with a 3.5mm plug on both ends to connect.

How do you plug in the jacks of a computer stereo?

You can see your stereo is the amount of connector is what color, and then the color into the seat is good! Set the volume on the control panel and you should be fine!

Which plug is the one that connects the stereo to the mainframe?

Generally it's the green one

Which jack do I plug the speakers into? Did I connect the right one? What are the six ports for?

The green one is the right one, the pink one is for the microphone, the blue one is for the audio input, the gray, black and yellow ones are for multi-channel surround sound, which are not used by the general users.

Host and audio how to connect

One, the computer on the two wires connected to the sound through the two holes of the signal input, positive and negative can be. Second, two speaker cable L and R connected to the speaker signal output of the two also, positive and negative can be. Principle: the computer generates sound signals from two lines to the speaker signal input, the speaker will increase its signal gain to the speaker signal output to the two left and right channel speakers. With four interfaces of this speaker is generally responsible for the bass cannon sound output.

Speaker plug connection?

2 * 1 two-center speaker cable

That is, you are connected to a speaker, or mono

Speaker cable is generally red and black, on the compensation plug in the middle of the two connectors connected to the red, the outermost connector connected to the black

How to connect the headphone connector to the audio cable

Light red, green, and blue, there is a ground line, use a multimeter to measure the line to find the ground line. Multimeter measurements on the line to find the ground line, and the red together, the remaining two, one connected to the white one connected to the blue on the good Q: For example, I found the ground line and the red together, but the audio line red with 2 ah Answer: Oh, the audio of the two red can be connected to the together, that is, the ground line of the audio Q: Oh, to find the ground line and that 2 with the red together with the rest of the 2 with the line and the white and blue randomly connected?

Computer speakers have two plugs how to insert?

Speakers generally only have a round plug, used to plug in the host panel or the back of the green round hole. A few speakers are a flat USB plug, just plug into any of the enamel SB jacks on the host.

Speaker cable how to connect what are the methods

1, first remove the plastic sheath of the audio and video connectors, and then use a screwdriver to loosen the screws that hold the speaker cable.

2, and then use a wire stripper to remove a section of the insulation of the speaker wire, about 1-1.5cm, and then the inside of the copper wire wire stranded into a strand.

3, the copper conductor will be inserted into the banana plug, and fixed screws, and then re-set into the banana plug insulation sheath, that is, the completion of the audio cable connector.

How to connect two wires for audio?

Please take a picture and upload it so I can give you an accurate answer.

The audio cables should be connected correspondingly, that is, one end is plugged into the audio output socket on the source appliance, and the other end is connected to any set of audio input sockets on the left side of the back of the amplifier.

Between the amplifier and the speaker to use the speaker cable corresponding to the connection, one end is connected to the back of the amplifier in the middle of the speaker terminals, the other end is connected to the back of the speaker speaker terminals on it. Note that the positive and negative poles should be connected correspondingly, and there should be no mutual short-circuiting.

How do I connect my Aiwa speakers with four connectors?

This problem is very simple: 1. Aiwa speakers behind two sets of clips (generally square arrangement), a red and a black is a group, connected to a stereo, the other group connected to another speaker. 2. There is a row of clips (generally 4, straight line arrangement) is the radio antenna input, which FM for the frequency modulation antenna, connected to a wire more than 1.5 meters can be; AM is the amplitude modulation antenna to be connected to a special frame antenna. 3. There are two groups of RCA interfaces, one group labeled AUX/VIDEO is the audio signal input interface, can be connected to MP3, cell phones, computers, TVs and other audio input signals to amplify; the other group labeled SROUNDSPEAKER and BASSSPEAKER (seems to be) is connected to the surround speakers and subwoofer speakers. If you connect a subwoofer, you should connect an active subwoofer. \r\n More about Aiwa speakers have four connectors how to connect, go to: see more content