What is the installation method of Yuba? What are the precautions for the installation of Yuba?

In winter, a Yuba can bring people a warm and comfortable bathing feeling, but many people don't know much about Yuba. The following small series will introduce the installation method, wiring method and precautions of Yuba installation method. I hope that through Bian Xiao's introduction, let everyone know how to install Yuba, install Yuba for the bathroom and enjoy a comfortable bath.

First, the installation method of Yuba

Installation method of Yuba 1 Get ready before you install Yuba. In addition, when installing toilet space to prepare pvc ceiling, it is necessary to open air holes and install ventilation window. The spacing of ventilation pipe holes is about1.5m. When installing, It should also be noted that the distance between Yuba centers cannot exceed 1.3 meters.

Installation method of Yuba 2. When you are ready, you must determine the installation location of Yuba. Bathtubs are generally installed directly above the shower area, such as bathtubs and shower rooms. Therefore, the ceiling of the bathroom space should be made of waterproof and moisture-proof materials. After installing the Yuba, the light bulb in the Yuba should be 2. 1 to 2.3 meters off the ground.

Installation method of Yuba 3. Remove all the light bulbs in Yuba, remove the spring of Yuba mask ring, and then remove the cover. If the interactive cable of Yuba is connected to the switch cable, you need to connect the other end of Yuba to the ceiling power cord. Open the Yuba junction box and make corresponding wiring according to the product manual. Then repair the junction box. Be sure to plug the extra wires into the ceiling so that the Yuba can be installed in the hole. Then connect the ventilation pipe, pull the pipe out of any place in the room, install it at the air outlet of the centrifugal fan cover, then insert the bath box into the hole and fix it on the ceiling. After the screws at the top are tightened, you can install the Yuba mask.

Second, Yuba installation method-wiring method

1. First of all, when we install Yuba, we must open the ventilation holes and choose the direction of the ventilation holes on the wall. This position should be located not only above the ceiling, but also below the air outlet of the centrifugal fan shell. Pour the water drops from the air pipe into the appliance and open the round hole at this position.

2. After opening the air vent, we can install the ventilation window. First, put one side of the ventilation pipe into ventilation window, and then fix the ventilation window on the other side of the external wall exit. Fill the gap in the vent.

3. Select the installation location of Yuba. In order to achieve better heating effect, the installation direction of Yuba is best in the center of the bathroom, and the ceiling material used is better. After installation, the height of the bulb from the ground should be between 2.1-2.3m. Too high or too low will affect the effect.

4. Because the keel should be installed when laying 30×40MM wooden documents, the opening size should be reserved when wiring Yuba, and the height of mezzanine space caused by ceiling and roof should not be less than 220 mm.. According to the size of the box itself, square holes with the same size can be cut at the product installation position on the ceiling, and the distance from the edge of the square hole to the wall should not be less than 250 mm

5. The next step is to repair the Yuba, remove the mask, unscrew all the light bulbs, remove the spring on the mask ring, and remove the mask.

6. Connect one end of the power cord to the switch panel. Pull the other end together with the power cord out of the top opening. Open the terminal cover on the cabinet and fix the terminal cover with screws. Then plug the extra wires into the ceiling so that the box can be inserted into the hole.

Three. Matters needing attention in installation method of Yuba

1. If you want to install traditional Yuba products, pay attention to the power cord used when wiring. Use copper wire with a width not less than1mm. In the wiring process, wires need to be inserted into plastic concealed pipes and buried in the wall. Because of the large amount of steam in the bathroom space, it is not suitable to use exposed pipes, especially in the renovation of old houses, which needs to be more standardized.

2. If there is a shower room in the bathroom space and an integrated ceiling is used, there is no need to install a separate shower room. Shower rooms are usually equipped with shower equipment. When taking a shower, the temperature will not be too low. Yuba is very waterproof. If it is directly installed in the shower room, it is easy to accumulate water vapor, which will make the product damp and easily cause potential safety hazards.

The above is what Bian Xiao introduced to you about the installation method of Yuba, the wiring method of Yuba installation and the precautions of Yuba installation method. Bian Xiao hopes that through Bian Xiao's introduction, everyone can learn how to install Yuba, and also hope that everyone will like Bian Xiao's sharing. If you still want to know,