Traditional laosheng ointment

Can you change it to boneless?

1, the original car has a boneless wiper, can it be replaced with a boneless one?

If the original car has a boneless wiper, it can be replaced with a boneless wiper.

However, it should be noted that it depends on the pressure of the wiper bracket of the model. For example, some Japanese cars have lower wiper bracket pressure. If you use a boneless wiper, the wiper may be unclear for a long time.

If this happens, it is recommended to use traditional bone curettage; If the bracket pressure is high, the wiper strip can be pressed on the glass surface, which can better reflect the effect of boneless wiper.

2. What are the common mainstream brands?

Our common mainstream wiper brands are probably these: Valeo, Bosch Bosch, Suntory, Denso, Champion, Wear-resistant, NWB, CAP, and Aiduo.

When replacing the wiper, it is not necessary to use the original wiper brand, as long as the size and interface are suitable for your own model.

In addition, in the non-4S shop channel, car owners can also buy the same brand products (not the same products of the original car, but only the same brand products), but the products of these brands will not affect the daily use of the car.

After searching, a silicone wiper was found, and the measured results were good, which fundamentally solved the shortcomings of traditional rubber wiper, while the specially treated silicone wiper had the special effect of "water repellent".

3. What's wrong with putting the wiper up?

In the hot summer, or on the day of heavy snow, we often see that the wipers of many vehicles are standing up. What's going on here?

It turns out that at noon in midsummer, the surface temperature of the front windshield of a car can be as high as 50 degrees. If the wiper is exposed to the sun for a long time, it may deform the wiper rubber. In the cold winter, erecting the wiper can prevent the wiper from freezing on the front windshield.

4. Is the way to polish the wiper reliable?

It is reliable to renovate the wiper by polishing it, but it is very particular about the technology. If the wiper is polished too hard or the sandpaper model is wrong, it is easy to deform the edge shape and surface of the rubber strip, but it is not worth the candle.

The steps of renovation are simple. First take down the wiper and clean it, then fold the fine sandpaper in half and clamp rubber strip. Then after wetting the surface of the adhesive tape with water, gently rub it with fine sandpaper from top to bottom for three or four times. Finally, rinse the polishing particles and put them back on the wiper arm.

5. Improper selection of glass cleaning agent will accelerate the aging of wiper?

If the front windshield is cleaned with detergent, I don't know whether the new wiper itself is bad or the detergent. Later, I will find that the progress of wiper aging has accelerated, and it is not as durable as before. So it is best to choose a special vehicle cleaning agent.

6. How to solve the problem of abnormal sound jump of wiper?

There may be four reasons for the abnormal sound of the wiper: first, the wiper strip is aging; Second, there is dirt accumulation on the blades of the wiper strip; Third, there is dirt on the front windshield surface; Fourthly, too low temperature makes the rubber strip hard; Fifth, frequent use of wipers under abnormal conditions (such as dry scraping).

If the wiper makes abnormal noise, the owner can solve it by "wiping toothpaste".

The specific steps are as follows: ① Squeeze out toothpaste and apply it to a corner of a wet towel; ② Wipe the edge of rubber strip repeatedly; ③ Wipe the wiped black dirt with a towel.

Summary:

As for the wiper, it can actually be said to be a cliche. This is a wearing part. Basically, it is not cleaned. If there is abnormal noise, it needs to be cleaned, refurbished or directly replaced.

When we buy wipers, we can buy them in flagship stores of some brands. For example, Valeo, Bosch and Sandoli are all mainstream brands, and we can buy them according to their sizes and corresponding interfaces.

In addition, we don't have to make boneless wipers. If the original car has a boneless wiper, pay attention to the bracket pressure of the original car when replacing the boneless wiper to avoid inapplicability after replacement.