The most detailed and reliable cork wall panel installation process specification

Introduction: as an important decorative material, cork wall panels are used to cover all the needs of the home furnishing, industrial decoration market style, not only in the family (entrance, TV wall, children's room, etc.), commercial places (such as hotels, offices, companies, etc.) commonly used, but also widely used in the corporate image of the display wall, beauty salons, restaurants, movie theaters, meeting rooms and other places. So, how exactly should cork wall panels be installed? If you want to install it yourself, how to start? Bunny today to give you tips, tell you the most detailed and comprehensive method.

Suggestions:

Prepare the following tools before installation:

Ordinary walls are recommended to use Henkel Baxter universal adhesive tools: brushes, knives, fixed gauge, ink pots, handle roller

Pre-construction preparation:

If it is a gluable wall, such as glass, tiles, plywood, rough walls, ICI walls, etc., you can directly clean up after installation.

Other wall cleaning: cork wall panels have good elasticity, so you can level some of the defective walls by yourself, but the installation wall should be as flat as possible and free of debris, so as not to affect the adhesion of the glue.

Installation process:

1, the preparation before laying:

Measure the area of the installation wall with a tape measure, and find the center of the wall, using a level ruler from the center of the vertical, horizontal each drawing an axis, from which the central axis point to start installing wall panels. Use an inkwell to trace the datum line to maintain balance when laying the floor.

2, the installation method:

The installation of the field: the center axis point as the starting point, the vertical axis for the edge, the horizontal axis for the bottom line, the right side to the seam, the installation of the first wallboard, and then installed in turn. First install an inter-area, use the roller to press, make the adhesive firm and flat. Then take this area as a reference for the installation of other areas. This installation method requires high, can not appear big error caused by wallboard edge seam is not aligned, the gap is large, affecting the aesthetic.

I-beam installation: also called bricklaying installation. Installation, also from the central axis point to start pasting, the vertical axis for the side line, the horizontal axis for the bottom line, the right side of the seam, installed the first row of wall panels, the installation of the second row of the first piece of the wallboard, the midpoint of the piece of wallboard as a starting point, will be pasted in the first row of wall panels of the first and second piece of wall panels of the seams, and so on, the installation of the third row, the fourth row of wall panels. After installation, use the roller to press, so that the paste is firm and flat.

3, adhesive application:

Installation of the wall as well as the back of the wallboard need to brush the glue to ensure adhesion of the glue, brush the glue to pay attention to the uniformity of application, brush the glue on the back of the wallboard, pay attention to the wallboard on all sides of the application, must be uniform, not too much, otherwise, in the installation, there will be glue seeping out of the seam edge, affecting the aesthetic. Brush glue about 15 minutes, wait for the glue to dry (to hand touch not sticky shall prevail) before installation.

4, laying

In order to maintain a consistent surface flatness, from the initial placement to the whole piece of uniform force afterwards. Each piece of the next place to use the roller to be fixed, each stick a part of the area after the roller for the whole press.

5, assembling

and the location of the corner of the wall will certainly appear with the wallboard size is not the same need to assemble the wallboard, will be repaired on one side of the floor and the corner of the wall is completely coincident with the other side of the wallboard and has been laid overlap placed, to determine the overlap of the location of the overlap of the floor to be repaired to be cut off the overlapping part of the floor. The floor has been trimmed close to the wall corner of the joint surface cut into a sloping surface, fastened between the corner and the wallboard, with rollers to fix the level.

6, flattening

After all the laying is completed, the individual protruding parts of the roller brush from the center of the pressure with the leveling, and finally all the wall panels with the roller brush with the leveling.

The above 6 points is the bunny for you to support the trick. In fact, cork wall panels are now the meat and potatoes of the decoration materials, because it not only has a decorative function, but also sound-absorbing function and heat insulation, anti-static function. As an example, cork wall panels sound absorption and noise reduction in the range of about 30 ~ 50 dB, widely used in a variety of places that require sound absorption, noise reduction, can create a quiet, comfortable environment, and 4 mm thick cork wall panels do not occupy indoor space. Whether you are modern or elegant, contemporary or traditional, you will be attracted by the charm of cork wall panels.