Lamp specification size introduction lamp installation method introduction

The lamp is a common lighting fixtures in our lives, should the consumer market demand for lamps and lanterns on the market now appeared a lot of lamp type, I believe that we usually have some contact with more or less in the life of it! We usually in contact with the tube when the estimated size of the tube specifications do not have some detailed understanding of it! In fact, the specifications of the lamp size to do some detailed understanding is very necessary, then the next small make up for you to introduce some knowledge in this regard, by the way, to give you an introduction to the installation of the lamp.

Lamp specification size

Lamp specification

With the continuous development of society, people's quality of life gradually become better, the use of lamps and lanterns are constantly being updated, which fluorescent tube specifications with the change? Immediately after we go together to see the fluorescent tube specifications under the relevant introduction! Fluorescent lamps are divided into traditional fluorescent tubes and LED fluorescent lamps. Commonly used fluorescent lamp specifications are T8, T5, T4 tubes." T" stands for "Tube", which means tubular, and the number given after T represents the length of the fluorescent lamp. LED fluorescent tube specifications are φ26MM*600MM, φ26MM*900MM, φ26MM*1200MM and φ26MM*1500MM.

Lamp specifications-size one

The size of the fluorescent tube is based on the lamp specifications. Traditional fluorescent tube specifications were T8, T5, T4, in addition to the T is on behalf of the "Tube" tubular meaning, the number behind is the diameter of the fluorescent tube size. The unit is inch. For example, T8 is 8 "T", a "T" is 1/8 inch. In the fluorescent tube specifications, the diameter of the T5 tube is (5/8) × 25.4 = 16mm; T4 tube diameter is (4/8) × 25.4 = 12.7mm; T3.5 tube diameter is (3.5/8) × 25.4 = 11.1mm; T2 tube diameter is (2/8) × 25.4 = 6.4mm.

Lamp Specifications - Size Two

Lamp Specifications - Size Two

The T8 tube is a fluorescent tube that has 8 "T "s. A "T" is 1/8 inch. strong> Tube specifications - size two

The size of the LED fluorescent tube is also based on the size of the tube specifications, such as φ26MM * 600MM, then his size is: length of 600mm, the diameter of 26mm. usually, LED fluorescent tubes because of the softer light emitted by the more acceptable to the people to use. LED fluorescent tubes are usually more acceptable for use because they emit a softer light. What is the general specification of fluorescent tube? In the fluorescent tube specifications, T12 tube diameter is (12/8) × 25.4 = 38.1mm; T10 tube diameter is (10/8) × 25.4 = 31.8mm; T8 tube diameter is (8/8) × 25.4 = 25.4mm; T5 tube diameter is (5/8) × 25.4 = 16mm; T4 tube diameter is (4/8) × 25.4 = 16mm; T4 tube diameter is (4/8) × 25.4 = 16mm. /8)×25.4=12.7?mm. Different models of fluorescent tubes have different specifications, we can pay attention to when buying.

Lamp Installation

1. To install a new fluorescent tube, insert the tube foot into the lamp holder and rotate the tube to secure it. Replace the lamp if it dims, flickers or goes on and off.

2. Repairing fluorescent lamps is easy with replacement. If you suspect a part may be defective, replace it with a new part. Start with the fluorescent tube or bulb. You can install a new tube, or if you're not sure if the tube is burned out, test the old tube in another fluorescent lamp, which you can remove from the fixture socket by turning it. Install the new lamp in the same way - insert the lamp leg into the socket and turn the lamp to secure it.

3.To install a starter in a fluorescent lamp, simply insert the starter into its socket and turn it to secure it.

4.If the lamp is not faulty, then try replacing the glow starter. Daylight luminaires are rated by wattage, so it's important to use the correct one for the lamp in the fixture. Remove the old starter in the same way as the old lamp, by turning it out of the fixture socket. To install the new starter, simply insert it into the socket and turn it to lock it in place.

5. Ballasts are also graded according to power, and like spare starters, spare ballasts must match the power of the lamp and the type of fixture. Ballasts are the least likely to fail and the most difficult to replace, so leave them for last when you start replacing parts. If neither the lamp nor the starter has failed, the problem must be the ballast. To replace a defective ballast, disconnect the circuit, disassemble the fixture, transfer the wires from the old ballast to the new one (one at a time to avoid misconnections), and reassemble the fixture

6. If the lamps, starters, and ballasts are all working properly but the fluorescent lamps still don't light up, check for a defective switch. If the fluorescent lamp is controlled by a wall switch, replace the switch, which will be detailed in the next section. If the fluorescent light uses a pushbutton switch, then you can replace the old switch with a new one of the same type. To de-energize the circuit before operating the switch, remove the circuit fuse or trip the circuit breaker.

What to do if the lamp does not light up

1, case 1: most of the time it is a lamp problem, change a lamp will be OK.

2, case 2: ballast failure, restart the ballast: the ballast wiring re-plugging, the fire wire zero wire to choose one of them can be.

3, ballast burned out, need to replace the ballast. General household fluorescent tube ballast are inside the lamp head. Pry open the lamp head, we can see a small integrated circuit block, that's it. We need to cut off the IC block from both ends of the lamp head and just keep the terminals that come out from both ends of the lamp.

4, will buy the ballast way wiring, re-power is OK.

The specifications of the lamp size and lamp installation methods and troubleshooting methods have been introduced for everyone, the lamp as an essential part of our daily life, a type of lamps we do some understanding is very necessary. After all, now our lives can not be separated from the lamp child this kind of lighting. In addition to understanding the specifications of the lamp size, we should also focus on this understanding of the lamp failure methods, as long as the mastery of the lamp failure methods can be resolved after some of the faults encountered in the future.

Tuba Rabbit online free for everyone to provide "each decoration offer, 1-4 local decoration company, 3 sets of decoration design program", and decoration to avoid pit strategy! Click on this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, you can get it free of charge~