Which type of sliding door track pulley is good

Summary: The sliding door track is good or not is one of the important factors to determine the quality of the sliding door, from the track, pulley type, to the size of the track, will affect the user's experience of the sliding door. Which type of sliding door track pulley is good? The following is an introduction to the sliding sliding door track size and common problem solving. Sliding door track which is good

Sliding door track can be roughly divided into: two directions can be pushed and pulled track, single direction and folding sliding door. Among these three folding sliding door will be more space-saving.

1, three-rail sliding door

Three-rail sliding door can be opened two-thirds of the space, more effective use of space and achieve good ventilation.

2, single track sliding door

Single track sliding door structure, which contains a door frame, door and track, characterized in that: said track has a first inner side frame and a first outer side frame, the first inner side frame and the first outer side frame of the upper end of the hook body is provided.

Sliding door track size

The general sliding door track is 84mm, generally reserved for 100mm, now there is a track width of 70mm. but this track corresponds to the sliding door border is also matching.

Sliding door pulley models

There are three types of plastic, metal, and fiberglass, they have some differences. For plastic pulleys, the texture will be relatively hard, so it is easy to use for a long time broken or astringent phenomenon. Metal pulley, although good quality, but the noise is relatively large. The glass material pulley, not only good quality, all aspects of performance is also good.

Sliding door track pulley installation

Track installation

1, in the sliding door above the installation of the track box, the height of the best in about 12cm, the width of the best in about 9cm.

2, first set three points on the track, respectively, at the two ends of the track and the middle position, and then install the upper track of the sliding door.

3, use the crane hammer to draw three points perpendicular to the ground, and then install the lower track, which can guarantee that the upper and lower tracks are on the same plane.

Pulley installation

First of all, lift the sliding door up a little bit, at this time the hand to reach the lower frame of the pressure pulley. Then take off the pulley, and to put it into the slot, but also remember to use the height adjustment screws against the hole screwed. Finally, after screwing the screws of the pulley in place, you just have to get the upper pulley to the screws and screw the screws of the upper pulley in place.

Installation notes

1, before installing the sliding door track, need to discuss with the carpenter beforehand to reserve the sliding door installation place, plan for the reserved place, and do a good job of the door set. Also need to install the sliding door of the place for accurate measurement, to avoid the size does not fit.

2, in the process of installing the sliding door track to be particularly careful, pay attention to protect the surrounding finished decoration, such as in the installation of the track to be careful when the cutter cut to the ground material, resulting in difficult to repair. Sliding door track do not do too wide, too wide will lead to sliding door stability is not high, easy to use shaking, will also affect the service life of the track.

3, sliding door track frame profile thickness can not be too thin, the frame thickness should generally reach 1.2mm-1.5mm, so that it will not shake, more stable. Some manufacturers in order to make the design of the sliding door more beautiful, the use of low-quality cold-rolled steel plate after molding carbon steel-type material into the door edge, the thickness of the profile is less than 1mm.

4, sliding door installation is completed to test the door of the whole is good to push and pull, whether or not it can be operated freely, can not be tightly closed. If installed in the kitchen and dining room between the sliding door can not be tightly closed, it will cause a lot of fumes run out to pollute the rest of the living room.

Sliding door track cleaning

Daily cleaning

1, then the most important thing is to keep the sliding door track clean in daily life, to prevent the entry of foreign objects, such as debris and dust in the track, first use chopsticks, sticks and other debris in the track to pick out. Remove the dust deposited on the bottom track, clean the corners with a rag dipped in water and dry with a cotton cloth.

2, to change the appropriate suction head, the particulate debris and hair sucked away, and then sprinkled with decontamination powder or lye, wait 2-3 minutes, fully dissolve the dirt, and then wipe with a wet cloth. This way most of the dirt in the track will be cleaned out. Then use a toothbrush dipped in stain remover powder, focus on cleaning stubborn dirt, soon the track will be able to present a new look.

3, rub the rubber band with your hand for 5 seconds, let the rubber band static electricity, put the rubber band into the sliding door track, use chopsticks to push the rubber band, so that the rubber band sucks up the stolen goods, and then use chopsticks to take the rubber band out!

How to clean with mud and sand

Available vacuum cleaner plus brush for cleaning, and then use transparent glue to stick out. For some of the more stubborn mud (dirt), it is recommended to pour water into the slot and then use a brush to scrub repeatedly.

Sliding door track pulley common problems

One, the sliding door wheel slippery inflexible how to deal with

1, the wheel out of the track, resulting in the sliding door directly and track friction. Lift the door directly, the wheel can be re-carded on the track.

2, due to the great weight of the glass door, easy to cause the wheel crushed deformation, wheel damage. At this time to re-replace the wheel can be.

3, deformation of the track, resulting in the wheel can not be free to roll lightly on the track. Need to adjust the track straight.

4, the slide and small wheel lubrication rust. Use lubricating materials with sliding door wheel track grease, first of all, the slideway carefully cleaned . The grease is applied into the slide and pulley, repeatedly pull the sliding door a few times, the grease will penetrate into the slide and bearings inside, and then pull it is very smooth.

Second, the sliding door pulley screws fell

Use a screwdriver to fall out of the screws according to the original position to the up.

Three, how to adjust the sliding door pulley

First of all, prepare a 5 mm or 6 mm hexagonal wrench; in the sliding door below the two sides of the side of the hole will be able to see, usually bumping the head of the cotton strip is plugged in the hole; after the insertion of hexagonal wrench into the hole and twisting the wrench, the opposite direction of the sliding door to adjust the low, positive direction to adjust the high; and finally adjusted to the door along the two sides of the bottom of the flat on the line.

Four, sliding door pulley rust how to do

Sliding door pulley can drop some grease and so on, so you can increase the lubrication, not to make a very harsh and unpleasant sound. As for some really bad quality, can only be replaced. As for the rust rust how to do? Very simple. With a hand drill, twist drill bit (size depends on the screws) to the rusty screws drilling through the pulley can be removed and replaced.