What is the threading method of wire rope for hand-cranked clothes hangers?

Wire rope threading method of manual clothes hanger;

First of all, you need to take out the accessories of the hand hanger, including hand crank, handle, pulley frame, corner device, lifting ring, fixing cover, expansion screw, wire rope and mortise. And prepare tools such as electric drill, tape measure and chalk. These are all needed when installing hand-cranked clothes hangers.

Next, find the installation position of the crank handle, preferably drilling at the height of 1- 1.2 meters from the ground, and then install the crank handle. Then start to determine the position of the corner device and install the corner device on the top of the house. It is worth noting that the position of the corner device needs to be perpendicular to the position of the hand crank.

After the installation is completed, start to install the four pulleys. Generally, the distance between the two sides of the pulley frame and the wall should be kept above 27cm, the horizontal distance in front of the two mixing wheels should be kept within the range of 18-20cm, and the vertical distance should be not less than 45cm. Of course, the specific situation has to be analyzed in detail. After all, every balcony is different in size.

After the position of the mixing wheel is determined, it can be punched, and then two expansion screws are installed on the single wheel frame, two expansion screws are installed on the double wheel frame, and two expansion screws are installed on the corner device. It is worth noting that six expansion screws need to be installed here.

Next, start installing the hand crank. First, fix the hand crank with the expansion screw and tighten it. Then install the handle, the same is true, tighten it with screws, and finally shake out the wire rope in the handle until the handle can't turn. It is worth noting that in order to prevent the occurrence of wire disorder, it is necessary to pull the wire rope when shaking it.

Then take out two wire ropes with the same length, use one wire rope to pass through the corner device, then pass through one of the double pulley frames, and pull the wire rope to the position close to the crank. Finally, pull all the steel wire rope at the other end through the corner device, then hang the button of a section of steel wire rope shaken by hand on the tail of the steel wire rope of the corner device, and finally install the fixing cover.

Next, pull out two wire ropes on the double pulley and thread them on the single pulley, and then install the fixing cover. Then, cut off the excess wire rope, and the cutting position is above the crank. Then, four lifting rings are sleeved on the two ends of the two air drying rods, and the two ends of the air drying rods are sleeved with plugs. This is the installation procedure of the air drying rod. After the drying rod is installed, two small accessories can be installed.

Extended data:

Precautions for installing hand-cranked clothes hangers:

1. There are four groups of ceiling pulleys, two of which are single bearings and the other two are double bearings. Double bearings are installed near the crank.

2. The fishing device is directly installed above the vibrator, about 1.5m from the ground. The height can be adjusted according to the specific situation, but the corner and the rocker must be kept vertical, so that the steel wire rope will not rub during use, and the shell of the vibrating screen (if the friction will produce burrs, it may break).

3. The threading method of steel wire rope should be as follows: starting from the corner, one bearing passes through the corner, passes through the bearing on the double bearing, and then passes through the crown block pulley of the other bearing, and hangs down through the lifting ring, and the hanger rod and the knot are fixed; The other end of the wire rope also passes through the corner bearing first, and then through the lower bearing of the double-bearing crown block, and then hangs down and knots, and is fixed by the lifting ring.

4. Fix four poles with lifting rings, then adjust the length of two steel ropes in the middle of the steel ropes, and fix them on the wire buckles of the steel ropes on the manual vibrator, and keep the poles horizontal. (Note: Sometimes, due to the different heights of buildings, the steel wire rope may be too long and part of the steel wire rope may be cut off).

5. Insert the club head into the rod again and connect it to the hook (12 expansion screw is divided into 4 internal expansion screws, 8 external extensions and 8 external extensions fixed on the ceiling). Some models use windproof clothes hangers, which are divided into windproof head and clothes hanger body and need to be assembled together, so it is easy to install windproof head in boiling water.