How many steps does it take to make a Chinese cheongsam?

I. Cut the paper pattern (the paper pattern must be checked correctly: shoulder, side, hem is equal in length and width)

1. Cut the front piece of the lapel (the center of the lapel in front of the 1cm seam)

2. Front piece of the bottom lapel stacking (cut the lapel after the lapel to leave a 6~7cm seam)

2. Cutting tablecloth (first fold out the width of the cloth, find out the direction of the pattern, and the center of the pattern of the main body, use an iron to iron out the center line)

1. Cutting the back piece:

(the back piece of the paper type on the end of the cloth, the neckline and the right-hand side of the leftover cloth)

(sewing portion to stay: side 2cm, hem 4cm, cuffs 0.7cm, with a sleeve to stay 1cm,

shoulder to stay 2cm, the neckline is not cut first. 2cm, the neckline is not cut first, when the shoulder line is good, and the front collar together)

(neckline and pleats with a line stapled to make a mark, or with a piece of powder to draw the pleats and neckline)

2. Cutting the front piece:

(the front piece of the right upper body because of the small lapel, so the first cut the upper layer of the fabric of the small lapel and lapel superimposed on the part of the lapel of about 7-8cm and then folded with the large lapel, cut the front piece)

(the seam left: side 2cm, hem 4cm, with a sleeve stay 1cm,

shoulder stay 1cm,

Not to be cut first, such as shoulder line, with a good collar to open)

( Sewing portion to stay: side 2cm, hem 4cm, cuffs 0.7cm, with a sleeve to stay 1cm, shoulder to stay 2cm, the neckline is not cut first,

waiting for the shoulder line to catch up, and the front collar to open together)

(the big placket to stay 0.5~1cm, the bottom placket to stay in front of the center of the bottom placket to stay 0.5~1cm, the lower stacked portion of the stay 7~8cm,)

(the neckline and the pleat with a line stapled to make a mark, or use the Powder sheet to draw the pleats and neckline line)

Three. Production procedures:

1. car pleats (ironing out the center line, sparse seams fixed) according to the marking sewing, pleat tip should be knotted with the car line, can not be back to the needle, (pleat left and right separately ironing) pleats small, pleats less, upward chamfering ironing, the car pleats, hem → diagonal needle stitching treatment, you can car cloth edge.

2. Bottom placket processing: fold 0.7cm~1cm car 0.8cm

3. Large placket processing: (1) on the embedded strip (1cm wide) (2) cutting and pasting

4. back body of the shrinkage of the ironing and embedded strips

5. front body of the shrinkage of the ironing and embedded strips

6. open the fork of the padded fork cloth

7. shoulder line. Sewing (the neckline and then back to the needle about 4 ~ 5cm, to avoid cutting the neckline after the separation)

8. cut the cuffs patch

9. do the collar

10. open the neckline (stand up with a ruler to measure, than the actual collar circumference of 3 ~ 4cm less than the sewing portion of the included)

11. on the collar (back to the needle sewing to fix the neckline must be hidden, but not sewed to the table fabric)

12. p>

12. Joining (sewing)

13. Drawing the position of the disk buckle and pinning the secret button mark, the bottom of the placket secret button under the cushion of fabric, sewing the collar hook

14. Use a slanting needle or hide the needle

17. Open the fork stops, zipper stops above the fixed anti-splitting

18.