Graphic video of how to remove the ball lock

Question 1: If the spherical door lock is locked, how to remove it outside the door is easy to get.

Knock the ball of the spherical door lock with a hammer and knock it off. After the ball falls, you can see a mechanical part with a cross or a straight line in the middle, a straight screwdriver or a cross screwdriver. Just put it in and twist it. It's as simple as babysitting. Remember not to kick the door open, or the door frame will crack. It will be inconvenient to change the lock then, and the door frame will be unstable. Even if the heart lock is installed, it is loose!

Question 2: How to remove the ball lock from the outside? I have a lot of experience in this field. I pulled down two doors this month. A balcony door and a kitchen door are inferior spherical locks installed by the developer, and there is no key. If it's closed for no reason, it won't open, causing me to jump into the kitchen from the window and pour water. We looked up a lot of information and could only demolish it destructively. Look carefully, there is a small eye on it. Take a screwdriver and turn the handle hard.

Question 3: How to disassemble the spherical door lock? Diagram and installation 1. First, disassemble the spherical door lock on the indoor side. There is an L-shaped notch in the ball near the central axis. Press the card horizontally into the notch with a screwdriver and the ball can be pulled out.

2. Turn the decorative cover (the cover close to the door panel) counterclockwise and remove it.

3. Unscrew the four internal screws and remove the fixing plate (round).

4. Pull out all locks from the outside of the door.

5. Loosen the fixing screw of the locking bolt and take out the locking bolt. It's over.

Installation is the reverse step. I hope I can help you.

Question 4: How to disassemble the spherical door lock? There is a long bayonet on the thin neck. If you push it in, you will pull out the knob and you will see the rest.

Question 5: The diagram of how to disassemble the outside of the spherical lock can only be smashed from the outside and cannot be disassembled normally. If possible, it will not be easy for thieves. If it is disassembled, it should be pushed out from the small hole inside, and then the spherical head should be pulled out immediately.

Question 6: How to unlock the spherical door lock? Put the bottle stopper under the video door.

Question 7: How to open the ball door lock video method 1

It can be clipped out or picked out with sharp tweezers or needles, and the ball lock can be disassembled in this way. On the rear knob of the ball lock, that is, behind the door, there is a ball connected to a shaft, and there is a small hole here. You can directly see a relatively small button. All you have to do is use wire or scissors, press this button, and then pull out the ball shell to open it. Then turn the decorative cover near the door, that is, a big round cover, and you will see two solid screws. Then unscrew the two screws with a Phillips screwdriver and the lock will be opened.

Method 2

Step 1: Open the lock.

1. Insert the iron plate (with special handle removal tool) inside the spherical lock fitting into the small hole below the handle.

2, according to the previous step, you can easily unscrew the grip.

3. Lever up the washer behind the handle with a screwdriver.

4. Loosen the fixing screw in the ball lock with a Phillips screwdriver or an electric screwdriver.

5. Remove the old ball lock from the other side of the ball lock.

6. Remove the locking bolt with an electric screwdriver or a Phillips screwdriver.

7. Remove the handle of the new ball lock assembly in the same way as step 1.

8. Remove the fixed locking piece and gasket of the ball lock.

9. Install the locking bolt first, and then install the ball lock to test whether the tenons of each other are accurately engaged.

10. Install the fixed locking piece with an electric screwdriver or screwdriver.

1 1, and install the spherical lock handle washer.

12. Press in the knob of the ball lock.

Step 2: Open the door and go in.

Step 3: Install the lock

1. Determine the center of lock body and lock tongue according to the distance template.

2. Draw a circle from two center points, drill a lock body hole with a diameter of 54 mm, then drill a lock body hole with a diameter of 25 mm, and dig a bolt wrench sleeve at the same time.

3. Remove the inner handle with the tip of the connector.

4. First, install the locking bolt into the locking bolt hole at the door side and fasten it with screws. Then, install the lock body, insert the lock body hole from the room, and fasten the tail end of the lock tongue at the same time, so as to combine the lock body with the lock tongue.

4. Adjust the position of the outer adjusting ring so that the center of the lock body is located at the center line of the door thickness.

5. Place the inner gloves on the handle tube, press down the locating cards with the closed ends of the fittings, and then push them into the inner handle to fix them.

6. If the lock can be opened flexibly with the key and the inner and outer handles, the lock is installed correctly.

Question 8: How to unlock the spherical door lock? Insert your tongue and stir the marbles with the iron groove.

Question 9: How to remove the spherical door lock and how to install it;

Step 1: According to the product manual, first paste the newly bought door lock with a fixed-distance template made of paper or cardboard at an appropriate position near the door.

Step 2: Use the electric drill of the hole saw to drill a hole in the lock core according to the specified size, and the drill tip should pierce the other side of the door, and then the other side of the door will finish drilling. (Note: Do not damage the finish on the other side of the door)

Step 3: Drill a comfortable hole at the edge of the station until it is connected with the lock core hole (the drill tip is at right angles to the door). Smooth the edges of the hole with sandpaper.

Step 4: Insert the locking bolt into the hole, fix it, and draw the outline of the locking bolt plate.

Step 5: Insert the lock tongue and the lock tongue piece into the mortise cut with a chisel, drill the screw assembly hole, install the screw and fix it in place.

Step 6: Insert the lock core of the external lock to make the lock core shaft or connecting rod adapt to the lock tongue assembly. Then insert the inner lock cylinder and fix it with screws.

Step 7: Determine the correct position of the locking tongue piece on the door frame, and drill holes with appropriate size for fixation (when installing the locking tongue piece with screws, it should be flush with the door frame.

How to remove the spherical door lock:

Step 1: First loosen the disc close to the door and twist it counterclockwise to make it retreat to the back.

Step 2: Twist the ball (that is, the hand-held part) a few times, look at the small hole on it, and hold it hard with a tiny thing to pull out the hand-held part.

Step 3: At this time, you can take out the loose disc, remove the two screws inside, and then pull it out of the door.

About the installation and disassembly methods of the spherical door lock, I only tell you here today. However, if you want to know more about the spherical door lock, I think you'd better install the spherical door lock yourself and then remove it. If you do this repeatedly, I think you can make the exercise perfect. Here, I would like to remind you not to hurt yourself when installing and disassembling the spherical door lock.