What is a dry-wet separation heating system?

The wet-dry separation system of the bathroom is to divide the bathroom into dry area and wet area for heating respectively, which makes the heating more reasonable. At present, only AIA has pioneered the wet and dry district heating system in the bathroom, which is warm in dry area and light wave in wet area. The heating effect is better, especially in winter. It is more comfortable to take a bath with the intelligent constant temperature system, and you are not afraid of freezing and catching a cold after changing clothes.

Advantages and disadvantages of wet-dry separation toilet

Divide the bathroom into two parts, dry and wet, so that the site outside the bath can be kept dry and sanitary, and the overall environment of the bathroom can be kept clean and beautiful.

Main advantages

1, improve safety: it will not slip because of splashing water on the floor;

2. Increase the usable area: concentrate water vapor locally for reuse in other places;

3. Extend the service life of the equipment;

Main disadvantages

1, dry-wet separation requires a higher bathroom area;

2, the cost is higher than the traditional bathroom design.

Origin: In the past, many bathrooms were designed with showers and toilets. In the old house, it is easy to see 1 multi-square-meter bathroom, and the shower is above the toilet.

Old-fashioned toilets are designed with multiple showers and toilets that are not separated, which leads to long-term water and humidity around the toilets, which seriously affects the use and sometimes accidentally slips. In order to improve the quality of life, the concept of dry and wet separation is put forward, that is, the bathroom is separated from other parts (such as the toilet), which makes it more comfortable and safe to go to the toilet.

Extended data:

If you don't want to buy a ready-made shower room and want to realize dry-wet separation, the most convenient way is to install a shower sliding door.

Door frame: The sliding door frame in the market is made of aluminum alloy, and the facade is made of PS plastic or more advanced tempered glass, which is rich in color and can be freely matched with the decoration style of the bathroom.

Glass: tempered glass has high definition and will not block the extension of sight. If it is necessary to strengthen privacy, you can choose sand-blasted or water-textured tempered glass. Its characteristics are: the cost is not cheap, but it is waterproof and mildew-proof, convenient to take care of, high in collision resistance and heat resistance, and there is no danger of cracking.

In fact, the well-built shower room not only occupies a small area and is easy to clean, but also has the advantage of gathering hot air.

Applicable people: people who have a strong design impulse, there is also an objective factor, the layout of the bathroom is not reasonable enough.

Design points:

1. The bathroom cabinet is separated from the ground.

The lower edge of the bathroom cabinet should be off the ground, which will cause some difficulty in installation, but you'd better do so. Because there will inevitably be water in the bathroom, which may be formed by washing the floor with you, and accidental water leakage is not ruled out. If the bathroom cabinet is separated from the floor, you can not only keep the floor clean and leave no dead ends, but also worry that the bathroom cabinet will be damp, which can kill two birds with one stone.

2. The inside of the cabinet should be separated from the outside.

Waterproofing outside the cabinet is done, and moistureproofing inside the cabinet can't be ignored. The work of the bathroom cabinet must be fine and fit. There are many ways to design doors and drawers, such as installing magnets and other adsorption switches on the doors and using automatic return tension springs on the drawers to ensure that moisture can enter without holes.

Step 3 set up a "steam barrier"

Before installing shower curtain, waterproof and moisture-proof treatment is the key point of toilet construction. The condensed water at the top of the bathroom often corrodes the ceiling, making the ceiling and walls prematurely aging. Before installing the suspended ceiling, a "steam barrier" should be laid to ensure that the rising steam will not condense on the cold floor and cause corrosion to the top.

In addition, the waterproof effect of the bathroom is related to waterproof materials. The use of environmentally-friendly waterproof materials can prevent water seepage and create a bathing environment that does not smell wet.

4. Anti-skid and moisture-proof in dry areas

The so-called dry-wet separation is only relative, so dry areas must also pay attention to moisture-proof and anti-skid treatment.

References:

Dry-wet separation-Baidu Encyclopedia