Traditional Culture Encyclopedia - Traditional virtues - How to use pipes correctly

How to use pipes correctly

How to use the pipeline, how to use the pipeline:

Methods/steps

1/9 Step by step reading

A pipe is not for smoking.

Beginners must first establish a completely different concept from smoking. The pipe is not used for smoking, but for natural breathing and breathing. Some people even say that it is light blowing and light sucking. Blow the first bite gently, blow through more burning, then blow another bite gently, blow out the fragrance, and then inhale gently. Again, hold your pipe gently and breathe naturally.

2/9

Don't be afraid to turn off the engine.

If it goes out, order it again. The novice is afraid of turning off the fire, so he keeps smoking, and his face is red and protruding. Afraid of flameout, you can live two breaths, not a few. Just like burning charcoal, the fire should be strong. No one can smoke. It must be windy. )

3/9

The pipes must be clean.

To enjoy the fragrance of tobacco, it is necessary to remove the ash and tobacco oil from the last bucket (gently wipe it with a paper towel). It is best to test whether the ventilation is smooth and whether there is any odor before loading cigarettes. Don't light the fire unless it goes well, or the pipe will die. Many people are generous when they buy cigarettes, but they are very economical when they buy coupons. When the coupon turns black, they are reluctant to throw it away.

But when cleaning the pipeline, you should scrape off the layer of slowly burning pancakes in the pipeline.

Don't disassemble the pipe before it is cooled, because the barrel and the cigarette holder are made of different materials and have different expansion coefficients, which will make it tight and easily hurt the pipe.

In addition, there is a special cleaning liquid for cleaning cigarette holders and cigarette holders, which is called (sweetening liquid). Soaking the sweetening liquid in the cigarette holder rod at regular intervals can completely remove the old scale and peculiar smell left in the cigarette holder and the cigarette holder hole.

Some use compressed air, which can not only clean the pipeline, but also eliminate the odor and leave the fragrance without damaging the pancakes.

4/9

Take out the cut tobacco and gently knead it.

Tobacco will be squeezed by packaging (whether it is paper packaging or canned), so rub it gently with your fingers. If it has been kneaded loosely, there will be pre-kneading marks on the package. It is one of the pleasures of smoking pipe to leave a faint smell of tobacco on your fingers after gently rubbing tobacco. Tobacco pieces must be loose.

5/9

How to pack tobacco

Many people say "stuffing" tobacco, and the word "stuffing" is one of the worst concepts of smoking pipes. This pipe won't smoke well if it is loaded with tobacco.

Gently knead loose tobacco into small balls and put them in the bottom of the barrel. Gently load the tobacco until the top of the barrel is flush, and press the tobacco down to five or six points with a tool.

Press the tobacco with your fingers to check whether it is elastic. If there is no elasticity, it means it is too tight. Be sure to take it out and reinstall it. If it's still loose, press it a few more times.

The technique of filling tobacco is the "mysterious ingredient" of tobacco, which can give full play to the fragrance, rhyme and strength of tobacco. On the other hand, it is the mysterious killer who ruined good cigarettes.

6/9

Take a few deep breaths before lighting the fire.

Many people like these mouthfuls because they taste the aroma of unlit tobacco, especially the special aroma of flavored tobacco. Even you can not light a fire (you have smoked enough today) and just enjoy the original flavor of tobacco. If poor ventilation is found, it means that the tobacco is too tight or the vent is blocked. At this time, just disassemble the pipe, put a strip or a smoke knife at the bottom of the pipe, and dredge the exhaust hole. Of course, it is best to take it out and reinstall it.

7/9

Ignition is a two-part process.

First, slowly burn a burning layer on the tobacco surface (surround the fire for 5 or 6 times). At this time, a lot of tobacco will stand up and gently flatten it with tools. This is the basis of whether this kind of pipe smokes smoothly or not.

Then there is the official ignition, which will make the tobacco smolder for more than 30 minutes.

Lighting matches is a great pleasure of smoking a pipe. In the world, everyone has the same pipe, the same amount of tobacco, plus two matches, and then they smoke longer than others.

8/9

Stop when you say so.

Beginners learn the correct basic skills after 20 to 30 strokes. At this time, if they want to turn it off, it won't turn it off. Just put down your pipe and don't smoke. It will go out. This is one of the controllable characteristics of the smoke pipe. Just smoke first and then ignite, and the combustion layer will burn out when igniting again.

9/9

Cold suction and slow fire

Cold smoking and slow fire are the keys to smoking a pipe. Only when the pipe is hot can the tobacco be smoldered slowly and the extreme taste of tobacco can be extracted.

If the pipe is too hot, don't smoke it until it is cold. You must smoke your pipe very short (don't smoke) and slowly (don't smoke frequently) to enjoy the fragrance of tobacco. If the pipe is too hot to last more than 10 second, it means that when you smoke, you are burning your pipe and tobacco. Heather is quite resistant to heat (burning), but it is a kind of wood after all. Excessive burning will burn out the beloved pipe.

Cold pumping and slow fire are the quality standards pursued by all tobacco companies. Not burning a pipe is the criterion for judging whether a smoker goes in or out.