Traditional Culture Encyclopedia - Traditional customs - How to tell if a fishing rod is good or bad?

How to tell if a fishing rod is good or bad?

Question 1: How to recognize a good or bad fishing rod. How to identify the good and bad fishing rod in the small yellow fishing rod network

Various fishing rods have their own characteristics, but in actual use also tends to have its relative versatility. If the carp rod can also be used for carp fishing, iso rods can also be used for freshwater fishing.

1, length: the length of the rod and fishing waters, the environment and fish species is extremely close. In freshwater fishing, the general selection of 3.6-5.4 meters long rod. When you are fishing far away from the fishing spot, you can choose 6.3 meters, 7.2 meters of fishing rod.

2, weight: the choice of fishing rod should be light weight. For example, for domestic competitive carp fishing tournaments generally use 3.6 meters long rod for the competition rod, usually used for recreational fishing rod generally choose 5.4 meters long rod.

3, the rod body: to be straight, the rod wall should be uniform, thick and thin, no hard wounds, no cracks.

4, the interface interface wall thickness should be consistent, the interface cross-section should be flat, the sections must be inserted with the socket tight bite, the rod's interface is neither too shallow, nor too deep.

5, the uniformity of the tuning performance: in the rod in the force after bending, the arc of a good rod is a gentle transition state, after removing the weight can be restored to its original state. The poor rod has a dead center in its arc, and can not be restored to its original state after removing the weight.

6, hardness: can be divided into soft tone, medium tone, hard tone. The hardness of the fishing rod can be tested according to a practical standard weight. When choosing a fishing rod, with a pre-prepared weight or temporary plastic bag filled with weighted bait, tie it to the tip of the rod, and then slowly raise the rod, when the weight off the ground so that the tip and the bottom of the rod handle to remain on a horizontal line. At this point, you can check that the stiffness of the rod matches the stiffness indicated on the rod by looking at how the rod bends.

Question 2: How to see the good and bad of the fishing rod How to see the good and bad of the fishing rod? Wike flagship store (Tmall sell fishing tackle) small days for you to answer:

At present, the domestic fishing tackle market sales of telescopic fishing rods, mainly divided into fiberglass fishing rods, carbon fiber fishing rods, due to the carbon fiber rods have a light weight, small drape, high strength, wear-resistant corrosion resistance, etc., by the vast number of anglers love. However, due to the complexity of the carbon fiber manufacturing process, our country can not yet mass production. In addition, carbon fiber is the manufacture of strategic missile warhead wear layer of the best materials.

Carbon fiber rod manufacturing process and fiberglass rods, are cut into a wide end of a narrow end of the trapezoidal soaked cloth rolled in a conical steel mold core, and then use a transparent glass tape into a spiral from end to end of its tightly rolled, and then placed in an electric furnace will be dried glue, and then taken out of the furnace will be out of the cross-core, removed from the body of the rod on the glass tape, after trimming, sanding, lacquer pulling, after assembly that is into the fishing rod. Due to the softness of the cloth that has just been soaked in glue and the tightness of the glass tape, the rod body will be strangled into an uneven spiral, rather than carbon fiber cloth or fiberglass cloth rolled into a spiral. Some fishing rod surface seems smooth, this is a machine will be the body of the rod protruding part of the grinding and then pull the lacquer system, so that more or less damage to the integrity of the fiber, the strength of the rod has an impact, if the grinding operation workers are not careful, will be the wall of the tube is too thin, then the rod's quality is too poor. The best way to do this is to buy a rod that has threads on it.

There are two ways to distinguish between carbon fiber and fiberglass rods: one is to look. Open the back cover of the rod body, if it is a carbon fiber rod can be seen on the rod body without pulling the paint part of the silver gray, and the same color as the carbon brush on the motor, the texture is fine and dense without weft lines. With carbon black powder dyed fiberglass cloth is darker, there are obvious weft lines, rod body rough. The multimeter will be dialed to the K file that is the resistance file, the two test rods at the same time on the rod body without pulling the paint, if it is a carbon fiber rod, the needle swings to the right, and vice versa is not moving.

Question 3: How to identify the good and bad fishing rods are now basically carbon rods

Carbon content can be seen on the logo on the rod box

Carbon materials are divided into many kinds of higher prices with the carbon cloth naturally the better

Fiberglass rods are very few nowadays, generally more than ten twenty dollars of fiberglass

The hard rods and soft rods are differentiated by the bending degree of the rods after stress

The hard rods and soft rods are differentiated by the bending degree of the rod body.

The curvature of the rod in the two-eighths of the rod is hard

The three-sevenths of the rod is the medium-adjustment rod

The four-sixths of the rod is the soft-adjustment rod

The hard-adjustment rod is generally used for fishing big fish or fast fly fishing

The soft-adjustment rod can be used for fine line and small hooks to play with the feel of the fish

The medium-adjustment is generally more adaptable to a wide range of sizes

The medium-adjustment rod is generally used for fishing big fish or fast fly fishing. The adaptability is wider, and it can be used for all sizes

Question 4: How to identify the good and bad rods? How to identify: 1. According to the economic strength to determine the price, according to the use of the decision of soft and hard. According to the need to determine the length.

2. First, the rod from the tip, a section of a section pulled out, observe the interface is good with, if the two sections of the rod interface gap is greater than 0.2 millimeters to consider, if greater than 0.5 millimeters do not buy.

3. Gently shake the rod, feel the rod body is trembling evenly, if you feel that the rod has an abnormal high don't buy

4. Observe the appearance of the rod, paint whether there is trauma, whether the rod is vertical, and then will be each section of the rod apart, observe each section of the inside of the smoothness of the ends of the cracks, if there is a crack or not smooth, don't buy.

5. The coupled two sections of the rod mouth to mouth inserted, check the residual length, in general, the bottom section should be in the forty millimeters, the top section of about twenty-five millimeters, and the rest of the bottom to the tip of the decreasing order. If a section of the difference is too large, do not buy.

6. Bring a line plate with you when you buy the culm, connect it to the rod when you pick the culm and hook the other end to a weight of more than half a catty, and observe whether the force of the rod is uniform or not.

Question 5: How to choose a fishing rod, how to distinguish the quality of the rod? Now more carbon. Roughly from two aspects to start shopping: First, you economic OK. Choose 300-500 above, of course, to good brand first. Lightway's is more secure. Secondly, if you want to feel yourself step by step. If you want to feel yourself step by step, it's better to start with more than 100. First, open the rod tail cover to see if the size of the tail ring of each section is the same size. Then straighten the rod to hold the rod, shake, see the whole rod's elasticity. Whether it is stable or not. If, when shaking the rod, only the middle part of the rod is shaking drastically, this kind of will not work. With a sudden flick of the wrist, the performance of the first two or three sections of the rod in the force, it is good. Third, to the effect of the rod overall paint, into the visual visual good or bad, whether there is uneven localization. Raised dots .... are not good. Four. Look at each section of the rod after tightening, each section of the match is no gap. Fifth, after straightening the rod, use your finger to play the middle part of the big section, listen to the sound, the sound is more brittle is good / sand sinking means bad. Almost all of the above points. The rest is up to the individual to summarize.

Question 6: How to distinguish good and bad fishing rods 1, when you see the rod, you must look at the inner core, because there is no paint, to see what material is made, you can distinguish good and bad, but also look at the pliability, because in the fishing, fishing posture is not good, it is possible to make the front end of the rod wear and tear, and then used for a long time, it will be easy to break can also be. Look at the parameters of the rod (length, weight, material, first diameter, meta diameter, suitable for the number of sub-line).

2. Look at the tuning of the rod (28 keys, 37 keys, determines the degree of hardness and softness of the rod) 3. Look at the center of the rod configuration (head-heavy rods, generally better strength, and easy to quickly transfer the tension to the rod waist, but the feel of the rod than the same weight of the rod heavy, the current more upscale rods, basically the head-heavy)

4. Look at the workmanship of the rod (the quality of the surface of the lacquer, the interface of the

4. Look at the workmanship of the rod (the apparent quality of the paint, the interface of the leveling and fit, open the bow to see the rod bending the integrity of the rod, etc.)

5.

6. Look at the reputation of the rod on the forum.

7, when buying a fiberglass fishing rod, to a section of the section out of the elongation, to see whether the rod is straight (the straighter the better), the head of the rod to not crooked for the best; look at the rod's paint is bright and tidy; whether the sections of the interface is tight and seamless, available to both hands hold the end of the rod, up and down the left and right shake a few times, such as the feeling of a "thumping" sound, indicating that the interface is not a good match. The first thing you need to do is to make sure that you have the right equipment for the job.

8. Measure the actual length of the rod to see if it matches the labeling, and the smaller the error, the better.

9, unscrew the back cover, observe each section of the annular cross-wall lamp thickness is consistent, whether there are cracks. If you buy a carbon fishing rod, in addition to the above three steps to check, you also need to fade out each section of the bright light to observe the inner wall is shiny. Good rods are as shiny as the bore of a gun

Question 7: How to distinguish between good and bad rods The main thing to look at is the grade of the carbon cloth (generally 20T-30T. 30T-40T for HVF and 40T-60T for SVF. SVF is lighter, stronger and more flexible than HVF: SVF refers to a super-strong, ultra-high-modulus carbon fiber of 46T-60T), which has a high modulus and a high strength, but is not as strong as HVF. and ultra-high modulus carbon fiber cloth, HVF refers to 30T-40T strength, high modulus carbon fiber cloth. The material of domestic common carbon fishing rod is generally 24T carbon fiber cloth. the higher the T value, the higher the strength and elasticity of the material.)

Secondly, look at the interface, workmanship

Thirdly, look at the feel, tonality, there is no head sinking phenomenon.

Lastly, look at the graphic

Question 8: How to see the good and bad of fishing rods in the online fishing rod sales,, appearance. Appearance is neat, the outer paint is evenly coated, no defects and exposed carbon cloth and so on. 2: rod wall. After unscrewing the plug to observe the rod wall of each section, the rod wall should be thin and thick uniformly consistent, there is no gap, thin and thick inconsistency, cracks, paint pollution and so on. 3: joints. The joint between the rod section should be uniform in length, not long and short or too long and too short. 4: Overall. After the rod shocked out, shaking is should not have a strange sound, such as snapping sound and so on. The rod thickness is uniform, the transition is natural, and the rod should be consistent with the nominal length, there should be no length, first diameter, metric diameter and the manual is inconsistent with the situation.

Question nine: how to choose a fishing rod Good fishing rod generally only look at so many standards, the first is the rod material, the rod material to be rich in toughness of the material, generally used is a composite material of fiberglass or carbon cloth to do, these two kinds of material is the big current. As for how to see the good and bad of this material can only rely on experience. The second is to look at the length of the standard, the length of the rod is generally only 2.7 ~ 6.3 meters and so on, the middle is 3.6, 4.5, 5.4,. This depends on personal preference, mainly depends on what kind of fish you fish, need more and more long rod, then you can. The third is to look at the hardness of the rod standard, the hand rod to withstand the pressure of the greater the better, the greater the tension to withstand that the rod is harder. The fourth is to look at the tonal standard, tonal is the strength of the rod, how to look at it, is the first to hold the rod, the rod slightly horizontal, and then look at the rod slightly can lift how much weight, look at the lifting of the weight of the II bending degree, if la the same weight, the bending degree of the lower the strength of the better, then the tonal more hard. Generally speaking, the rod's tuning is divided into five grades: medium, medium soft, hard, super hard, and extremely hard. Fishing rod quality can go to the small yellow fishing rod network

Question 10: How to test the performance of the fishing rod Fishing rod is one of the essential weapons for fishing, the rod is good or bad directly affect the fishing process. How to choose a fishing rod which has become the topic of most fishing enthusiasts often talk about, in view of this I collected some information on how to choose a fishing rod on the Internet for your reference, at the same time to say that the choice of a fishing rod do not blindly pursue the high price, suitable for their own is the most appropriate!

A how to choose a fishing rod

First look at the rod's outer paint surface is smooth, there is no bulging bubbles, or paint impurities and left uneven places, you can use your hands to touch. Then look at each section of the rod mouth is neat, wall thickness is uniform. It should be noted that the front and back should be looked at.

After looking at the appearance, each section of the rod all pulled out, and then insert the rod in the opposite direction after a section, for example, a rod from the tip of the rod to the back of the number of **** six sections, then the first section of the tip of the rod in the opposite direction of the insertion of the second section, to see the rod mouth outside the tip of the residual amount of length, at least in the more than 2 centimeters, and in turn, the second section of the reverse direction of the insertion of the third section. This method is used to check the amount of lap in the rod internal connection, lap should be in the normal should be between 2.5 centimeters and 5 centimeters.

After checking the amount of overlap of the rod, after the rod is assembled, the rod section by section will be pulled out all the unfolding, and then gently shake the rod to see if there is any unusual sound, if there is, it means that in one of the interface parts of the gap exists, the lap is not tight. After checking which section, the overlap will be tight, and then gently shake again, if there is still this phenomenon, then the price is even lower can not buy. Because this kind of rod increases your chances of breaking the rod, folding the line and running away from the fish. While checking the rod as a whole, pay attention to which part of the rod starts to bend when you gently shake it, so we know why the rod is tuned.

Put a fully extended rod on a finger and slowly adjust it until the rod is in a balanced state, then the point where your finger is on the rod is the rod's point of gravity, and the more the point of gravity is oriented toward the tip, the more the rod's gravity is oriented toward the front. A normal rod's point of gravity should be no higher than the first section. Lastly, remember to ask the owner of the tackle shop if the rod has original sections and other after-sales service issues. When everything is clear, you can buy

Second, how to choose a fishing rod

A well-made rod with beautiful shape not only allows you to enjoy the fishing *** and fun, but also reduces physical exertion and ensures that the number and weight of the catch, so how to choose a fishing rod has become a critical issue for beginners. Each rod has its own applicability and relevance, and beginners should choose a rod based on a number of factors at the beginning of the selection and purchase.

How to choose a handy and satisfactory fishing rod, I think we should consider the following aspects: First, what is the object of fishing fish species, is the carp or carp; second is the nature of fishing, is the nature of recreational fishing or competitive fishing; third is the material of the fishing rod, is the fiberglass or carbon fiber; fourth is the tuning of the fishing rod, is the two-eighths of the tuning or the three-sevenths of the tuning, four-sixths of the tuning; fifth is the length of the rod, also includes the use of long sections or the use of a long section of the rod. The first is the length of the rod, including whether to use a long section or a short section of the rod; the sixth is the family income status, and so on.

Choose a fishing rod should grasp the main points: the first step, first check the appearance. Look at the body of the rod text and pattern is clear, whether it is clear: whether the "three no" products; there is no ISO-9000 quality certification text; the second step, the rod with armpit clamp, from the most detailed draw, section by section inspection, to see whether there are cracks and scratches, between the section of the joints and section of the grinding gap; the third step, and then look at the rod is straight, and then shake your hand a few times, feel whether it is straight, and then see whether it is straight, and then see whether it is straight. The third step is to see if the rod body is straight, shake your hand a few times, feel whether there is a "gada" sound, if there is such a sound, it means that the rod mouth grinding is not good; the fourth step will be the last end of the rod body leakage cover open, check the ends of each section to see the inner wall cleanliness, to see whether the wall of each section of the rod is uniform; the sixth step, and finally look at the rod's tuning, whether it is in line with the requirements of angling.

I hope that beginners in the grasp of the key points on the basis of, but also comparison shopping, for their own to buy a real price satisfied with the fishing rod.

Three How to choose a fishing rod

The first thing you need to do is to look at where the manufacturer is, many fake products are labeled as being produced in Japan, South Korea, and cheaper, then you have to be careful, the real rod in the rod box is more labeled with the name of the manufacturer or trademarks most of the Chinese instructions, do not just look at the packaging is beautifully foreign words recognized as imported products.

The weight of the rod is the weight after removing the front and rear plugs and line handles. There are a lot of manufacturers who mark the weight of the rod very low in order to sell it, so don't just look at the labeling on the package and ignore the real weight of the rod. Low deadweight does not mean ...... >>