Operation method of intelligent remote control fishing raft

1. Names and operating instructions of various parts of the ship (see figure):

1. power switch: specially designed waterproof switch with transparent waterproof and anti-collision cover at the switch.

2. Charging socket: Insert the charger plug into this socket to charge the car battery.

3. Antenna: It is a metal antenna. When in use, it is installed on the ship.

4. Bait cabin: There are two cabins filled with bait, and the opening of the hatch is controlled by the remote control.

5. Hook device: There are left and right hook devices. When in use, the hooks can be hung on the hook devices respectively. The opening of the hook device is controlled by the remote controller. 6. Fish probe: Install a probe cover where the fish probe is installed. In configurations d and c, remove the probe cover to install the probe.

7. Lighting: The lighting is turned on and off by the remote control.

Headlight (white): it is a high-power LED lamp used for lighting; ,

Taillight (blue): it is a high-power LED light, which is used to indicate the direction of the ship;

Night vision light (red): The night vision light is configured separately. When in use, open the rubber plug of the socket on the ship and insert the plug of the lamp into the socket; 8. Battery cover: On the left and right sides of the ship, open this cover when loading batteries.

9. Waterproof grass cover: at the stern propeller, prevent weeds from winding.

2. Names and operating instructions of each part of the remote controller:

2- 1 Names and descriptions of buttons on the remote controller (see figure):

1 joystick (MANU): The joystick can be used to manually steer a ship.

Forward: slowly push the rocker forward and the ship will move forward (left propeller turns left, right propeller turns right).

Backward: slowly push the rocker backward, and the ship will move backward (left propeller turns right, right propeller turns left).

Turn left: slowly push the rocker to the left, and the ship will move to the left (the left propeller will not turn, and the right propeller will turn right).

Turn right: slowly push the rocker to the right, and the ship will move to the right (the right propeller will not turn, and the left propeller will turn left).

Stop: when the rocker is in the middle position, the propeller stops rotating (the rocker automatically resets) (the ship's running status can be displayed with an arrow on the LCD screen of the remote controller, and the arrow direction is the bow direction).

2. Hook open key (see icon): Press this key to open the hook on one side of the ship. Repeat the operation just now, and the hook on the other side will also open, and its working status will be displayed on the display screen as an icon.

3. Bait door opening key (see icon): Press this key to open the bait door on one side of the ship. Repeat the operation just now, and the warehouse door on the other side will also be opened, and its working status will be displayed on the display screen with an icon.

4. The key to the remote control of ship lights (see the icon): remote control boat's front and rear lights and night vision lights are turned on and off.

5. Automatic button: By pressing this button, the ship can be locked by the electronic compass and run automatically. When the ship is driving automatically, the LCD screen shows AUTO. When manual driving is required, press this key again to stop automatic driving.

GPS menu selection key (GPS): press this key to enter the GPS menu, and there are 1-8 digital cursors to choose from, one of which flashes to indicate the position of the key to be selected. Every time you press this key, you will skip a cursor. After the cursor jumps to "8", it will automatically return to "1".

7.GPS setting key (set): After selecting the icon, the cursor box selected by pressing this key for 3 seconds turns black and flashes, indicating that the address is set successfully. If you need to cancel the setting of the cursor, you can open the selection key again, find the cursor to cancel, and then press this key for 3 seconds, and the icon box will change from black to flashing, indicating that the setting has been cancelled.

8.GPS automatic navigation and driving key (GO): Press the menu selection key of GPS key to move the cursor to the desired target point and find the set destination. Press this key, and the ship will automatically navigate and drive according to the set address. At the same time, the current destination address (G 1-G8) is displayed on the display screen. If you want to cancel the automatic navigation function in the automatic navigation state, press it again.

Select the key (GPS) in the GPS menu or the key (GO) in the GPS automatic navigation to turn off the automatic driving function of GPS navigation and change to manual driving.

9.GPS menu selection exit key (ESC): press this key to exit the GPS menu (the set GPS target address will not be cancelled).

10. Automatic demonstration function key (demo): press this key to automatically demonstrate the ship's driving state (straight or turning), bait casting, hook hook picking, lights on and off, fish finder simulation signal, and repeat this action.

1 1. Screen backlight selection key (LCDL) and menu selection key (+): When the light is weak, press this key directly to turn on the screen backlight. When the menu key opens, use this key to modify and set the selected menu.

Note: When the screen backlight is set to ON, the backlight will always be ON, which consumes a lot of power. Will reduce battery life, so it is best to use this function in the dark.

12. Alarm sound elimination and menu selection key (-): When the alarm sound is not needed, press this key directly to eliminate the sound. When the menu key is opened, use this key to modify and set the selected menu.

13. MENU key: (menu) Press this key to select five menus. After selecting the menu, press the menu selection key to set it. After setting the menu, press the menu key again, and the menu will be set and saved (note: all five menus must be pressed continuously to save the set menu).

Press the menu key to make the following selections:

13- 1. Select the fishing boat type: ship type.

A:) basic type A B) basic type +GPS type B C) basic type +GPS+ fish finder type c

13-2. Select the communication channel of the remote controller:

Communication ADDR channel 0, channel 1, channel 2, channel 3 and channel 4.

There are at most 5 channels to choose from (note: the channel selection has been set at the factory, and it is not necessary to set it in use. Only when the same ship and the same channel are found to be in use and interfere with the ship should the channel be changed. When changing lanes, two ships in the same channel should be closed at the same time and then opened separately after changing lanes. (The scarlet letter is cancelled)

13-3. Fine-tune the left and right motor speed: MOTO ADJU

L:50- R50 indicates the rotational speed of the left and right motors. When the rotational speeds of the two motors are inconsistent, press the selection key (+,-) to adjust. .

13-4. Degree-day metric/English conversion: temporary unit:

Celsius: Fahrenheit:

13-5. Metric/English conversion of measurement unit: depth unit.

Meters: meters feet: feet:

13-6. Turn the fish icon on and off:

After turning off the fish icon, you can better grasp the number and size of fish; Open the fish icon to see if there are fish and shoals of fish underwater.

14) on/off: press and hold for 2 seconds to turn on the power switch, and the LCD screen will display various data of the ship. At this point, if the ship is not open,

When the power is turned on, the buzzer will buzz. The ship's power supply is turned on for 7 seconds, the signal is connected and the buzzer stops. (If

If you don't want to hear the buzzer, you can choose to turn it off.

15) USB charging socket: connect a charger for charging.

2-2 Display Description (see figure):

1 icon display description:

Signal strength: indicates the signal strength between the ship and the remote controller. When the signal is strong, the signal indicates that the battery is full; When the signal is weak, the number of signal cells decreases; When there is no signal, the signal represents X. ..

Battery capacity: display the battery capacity of the ship and the remote controller respectively. When the battery capacity is sufficient, the battery capacity indicates full capacity. When the battery capacity decreases,

The number of batteries decreases, and when the battery runs out, the battery indicator goes out.

Hook open: when the hook is closed, the icon is displayed as "T"; When the hook is opened, the icon of the hook is "one". If the boxes of both icons are "one", it means that the hook is loose. Press the hook key again and the icon will return to the "T" state.

Bait cabin is open: when the bait cabin is closed, the rectangular icon display frame is mesh; When opened, the box of the icon is white. If the boxes of both icons are white, it means the feeding is over. Press the bait bin open key again, and the icon will return to the closed state.

Ship's driving state: the icon is indicated by an arrow, which indicates that the ship is moving forward, while the arrow is pointing backward, which indicates that the ship is turning left (or right) (note: the front of the remote controller should be in the same direction as the bow).

Note: When the remote controller is placed horizontally, the direction indication between the ship and the remote controller is the most accurate. If the remote controller is placed vertically or obliquely at a certain angle, the arrow direction between the ship and the remote controller will deviate.

GPS satellite signal: The icon is represented by the origin of gammon, the icon flashes to indicate that it is searching for satellite signal, and the flashing stops to indicate that the ship receives satellite signal.

River bed landform (fish finder): River bed landform is displayed by different reflected waves generated by sonar on underwater river bed.

Fish icon (fish detector): The different reflected waves generated by sonar to suspended solids in water are represented by fish icons, which is convenient for identifying fish conditions. Automatic display of fish detector: automatically display the simulated signals of riverbed contour, fish icon, water temperature, water depth and depth range.

2. Description of digital display:

Display the effective travel time (GPS) of the ship: Turn on the remote control, and the number on the LCD in the upper right corner is 0. When the ship is running, it starts to time, and the ship stops at the same time, so as to master the effective running time of the ship.

Note: This data only records the information when the remote control is turned on, and has no recording function. After shutdown, the restart count time returns to 0. Display the distance traveled by the ship (GPS): After the flashing of the satellite signal stops, the distance between the starting point and the destination of the ship can be measured by setting the starting point, and the distance traveled can be displayed in increments of 5 meters.

Water depth (fish finder): shows the water depth when the ship is running. When the probe is put into the water, the water depth reading will be displayed on the screen.

Water temperature (fish detector): display the water temperature, turn on the remote control and the temperature reading will be displayed on the screen.

Depth range (fish finder): the depth range * * * has four grades: 0-4, 0-9, 0- 18 and 0-36, which can be automatically adjusted according to the change of water depth. The depth reading is displayed on the screen. If the depth is out of range (0.6 ~ 30.4m), the screen will display "-".

3 English display instructions:

Ship's driving mode:

Manual driving: MANU, automatic driving: auto, automatic demonstration: demo,

Automatic navigation mode of GPS navigation: G 1-G8.

Select fishing boat type: ship type.

A:) type a, type b, type b, type c, type c

Select the communication channel of the remote control:

Communication ADDR channel 0, channel 1, channel 2, channel 3 and channel 4.

Fine-tune the left and right motor speeds: MOTO ADJU L:50- R50

Degrees-Days Metric/English Conversion: Temporary Units:

Celsius: Fahrenheit:

Metric/English conversion of measurement units: depth units

Meters: meters feet: feet:

Switch between fish icon and reflection point: fish on/off.

2-3 Remote control sound alarm:

1 weak voltage alarm:

1) When the battery capacity indicator on the ship starts to decrease, it means that the ship can still run 10 minutes. When the buzzer on the remote controller makes a "drip" sound, the ship stops working;

2) When the battery indicator light on the remote controller starts to decrease, it indicates that the battery is low. When the buzzer on the remote controller makes a "drip" sound, the remote controller stops working;

2 weak signal alarm: when the remote controller can't receive the ship signal, the buzzer of the remote controller will make a "beep" sound.

note:

1) When the battery power is insufficient, the signal will also weaken and the ship speed will slow down;

2) When the ship runs within a certain distance, it will sometimes encounter other signal interference, and the signal received by the remote controller will be weakened and will generally recover automatically.

3) When the ship runs within a certain distance, if it encounters strong interference, the remote controller can't receive the signal sent back by the ship, and the buzzer will beep, indicating that the signal has been lost and the ship will spin in the same place. At this time, the ship's central controller will start the automatic signal repair function and restore the signal state within 2 seconds.

Three GPS satellite navigation:

3- 1 GPS operation steps (including ship operation steps):

1 Start-up inspection: the remote controller receives the signal, the battery capacity, the lamp, the bait compartment and the fish hook are turned on, and the motor is driven and controlled to rotate manually and automatically respectively, and the antenna is installed;

2. After the ship is turned on, GPS begins to automatically search for satellite signals. When the signal icon flashes and stops, it means that the signal has been captured.

3 bait hook (the fish hook can be directly hung on the connecting rod of the hook device);

4 put the boat into the water;

5 After the GPS signal is normal, open the GPS menu key and select the GPS starting point;

Note: the departure point must be set first after the GPS signal is normal, otherwise the ship cannot automatically return to the original departure point, and the distance of the ship cannot be displayed on the screen.

6 Press the GPS setting key (set) to set the selected starting point (press "1" to flash the cursor for 3 seconds, and the icon box turns black and stops flashing, indicating that the setting is successful);

7. Select the manual driving mode and the automatic driving mode to control the ship, and at the same time, check the LCD to display the ship's direction (indicated by the arrow) and constantly correct the ship's course;

8. Check the riverbed landform outline, water temperature, water depth, depth range and fish situation displayed by LCD;

9. If fish is found, press the bait opening button of the remote controller, and then press the hook opening button, and the bait bin door and hook switch on the ship will be opened respectively, and the bait and hook will be thrown into the water;

10 Open the GPS menu key and select the destination (cursor 2-8 can be set as the destination);

1 1 Press the GPS setting key (set) to set the selected destination;

12 If you return, please open the GPS menu key and adjust the cursor to the starting point setting of "1";

13 Press the (GO) key, and the ship will automatically return to its original starting point. After returning to the starting point, the ship will stop driving and automatically quit GPS navigation and change to manual driving mode;

14 Open the GPS menu key and adjust the cursor to the set destination;

15 Press the (GO) key, and the ship will automatically travel to its destination. After arriving at the destination, the ship will stop, and it will automatically quit GPS navigation and change to manual driving mode.

When the ship enters the GPS navigation mode, the LCD displays "G 1-G8", and when the GPS navigation reaches the departure point and destination, the LCD displays "MANU".

Note: The cursor address 1-8 in the GPS selection key can be each other's origin and destination, and users can choose it at will as needed.

Install 3-2 global positioning systems.

If GPS is used as an upgrade component, the installation steps are as follows:

1) The control circuit board of the electronic compass is installed at the bow, and the socket for installing the GPS module and four copper columns for fixing the module are left on the circuit board. Insert the GPS module and fix the module and copper column with nuts.

2) Turn on the power switch of the ship and the remote controller, and select menu key configuration. When receiving satellite signals, open the GPS menu, select and set one of the destinations, indicating that GPS has been installed and started to work.

3-3 Note:

* Because the satellite signal strength will be affected by the weather or current geographical location, the time to capture the satellite signal will change with the change of the current satellite signal strength, generally within 1 minute. After the satellite is captured, it usually takes 5 minutes for satellite navigation to work normally. Before this, if the departure place is to be set, there will be a big error when the ship returns.

* If the starting point and ending point of navigation are not set, GPS will not be able to complete the navigation function;

* The weather will affect the sensitivity of GPS. When it is cloudy or the clouds are thick, the time for GPS to capture satellites will be extended;

* Indoor signal is weak, please use it outdoors;

* Communication tower will interfere with GPS, so it should be avoided around here;

Four fish detector

4- 1 The function of fish finder:

The fish detector consists of sonar probe, central controller and LCD. Sonar emits ultrasonic waves into the water and sends them into the water.

The reflected wave of the object is displayed on the LCD screen of the remote controller after being processed by the central controller, so that we can clearly understand the outline of the river bed, water depth, water temperature, depth range and the activities of fish schools for foraging and fishing.

4-2 Installation of Fish Detector:

Open the upper and lower covers of the ship and install the probe and control panel of the fish detector, as shown below:

1) Installation of probe: Take off the probe cover, drill a round hole of ￠5mm in the bottom of the ship, and pass the probe data line through the bottom of the ship.

The sink and probe are fixed to the bottom of the ship with screws. Fill the waterproof cabin with waterproof sealant, cover it with waterproof cover and fix it with screws.

2) Installation of control panel: There are four control panel installation holes in the bow of the lower cover, so as to install and fix the control panel.

3) Connection between control panel and central controller:

The control panel has three sockets, which are respectively connected with the probe data line, the power line and the control panel signal line. The connection method is as follows:

A) Connection of probe data line: the probe data line passes through the bottom of the ship, and the terminals of the four lines are respectively put into the rubber shell of the socket in turn and connected with the probe signal socket of the control panel (terminal installation of the socket: hold the terminal of the data line in the left hand and hold the plastic shell of the socket in the right hand, and press yellow,

Black, blue, and thick black are arranged to insert the terminals into the rubber case respectively);

B) Connection of power cord: connect the control panel with the power output socket of the central controller;

C) Connection of control board signal line: Connect the control board with the socket of the central controller.

D) After installing the fish finder, turn on the remote control and select the menu button to configure C. The LCD screen has signal indications of water temperature, water depth and water depth range, indicating that the fish finder has been working normally.

4-3 Note:

* The ship should handle with care to avoid damaging the sonar probe at the bottom of the ship;

* The depth range of this machine is 0.6-30.4m. Beyond this range, this machine will not work normally.

* Fish detector is based on the principle of underwater ultrasonic reflection to scan fish. It is neither a camera nor a video recorder. It has no camera effect in the water, and it is impossible to identify the shape of each fish and the number of fish. It is also impossible to distinguish fish from other suspended substances, such as suspended aquatic plants, turtles and bubbles.

* According to the reflection principle of sonar, the reflection point of a big fish is large. The remote controller sets the switch between the fish icon and the reflection point. When the fish icon is off, you can use the reflection point to observe the size of the fish. When a fish or a group of fish is found, an object with a large reflection point and swimming can be judged as a big fish.

* Don't install two identical fish detectors in the same area, which may cause the machine to fail to work normally due to ultrasonic and RF interference.