What is the installation tutorial of aluminum honeycomb panel ceiling? What are the precautions for ceiling installation?

When decorating a house, many people will pay attention to the overall decoration style, but in fact, in order to improve the quality of house decoration, it is best to consider the details of various factors. The ceiling is a problem. Although most people want to make aluminum honeycomb ceiling, what is the installation tutorial of aluminum honeycomb ceiling? What are the precautions for ceiling installation? When decorating a house, many people will pay attention to the overall decoration style, but in fact, in order to improve the quality of house decoration, we must consider the details of various factors. The ceiling is a problem. Although most people want to make aluminum honeycomb ceiling, they only look at other people's works and don't know the installation procedure. Then the question comes, what is the installation tutorial of aluminum honeycomb ceiling? What are the precautions for ceiling installation?

What is the installation tutorial of aluminum honeycomb panel ceiling?

1, elastic line

Use a level to copy out the horizontal points at the corner of each wall (column) indoors (if the wall is long, several points should be copied appropriately in the middle), pop up the leveling line (leveling line is generally 500㎜ from the ground), measure it from the leveling line to the ceiling design height, and use ink lines to pop up the leveling line along the wall (column), which is the lower leather line of the ceiling grille. At the same time, according to the grid ceiling plan, the position of the main keel pops up on the concrete roof.

2, fixed boom

Fix the boom with expansion bolts. You can use Ф 6 sling. Hangers can use cold-drawn steel bars and round steel, but round steel should be straightened mechanically. One end of the grid ceiling suspender is welded with L30 * 30 * 3 angle code (the aperture of the angle code depends on the diameter of the suspender and the expansion bolt), and the other end can be threaded on the screw greater than 100㎜, or you can buy finished screw welding.

3, light steel keel installation

Light steel keel should be hung on the suspender (if the ceiling is low, this process can be omitted and the next process can be directly carried out). Generally, 38 light steel keels are used with a spacing of 900 ㎜ ~ 1000 ㎜. The light steel keel shall be installed parallel to the longitudinal direction of the room, and at the same time, it shall arch, and the arch height shall be 1/200 ~ 1/300 of the room span. Cantilever section of light steel keel with grille ceiling should not be greater than 300mm, otherwise suspenders should be added.

4, spring installation

Connect the light steel keel with the suspender (if the grille ceiling is low, the spring leaf can be directly installed on the suspender, omitting this process), with a distance of 900 ㎜ ~ 1000 ㎜, and then clamp the spring leaf on the suspender.

5. Assembly of grid main bone and auxiliary bone

According to the requirements of design drawings, pre-install the main and auxiliary bones of the ceiling grille below.

What are the precautions for ceiling installation?

The boom is overloaded, the wooden boom is split, or the steam is too short and too little.

The suspenders on the ceiling are few or too thin, and the weight of the ceiling exceeds the force that the suspenders can bear; The wooden suspenders are cracked or the nails are too short and thin; When it takes a long time or the ceiling shakes, it will cause the ceiling to deform or even collapse.

Second, when installing suspenders, drill holes in the precast floor.

It is difficult to install suspenders on the ceiling of precast floors. If the suspender hits the hole of the prefabricated perforated plate, the suspender will not be fixed, even if it can be temporarily fixed, but it is difficult to bear the weight of the ceiling only by fine stone concrete with a thickness of about 20mm, and it is easy to collapse and deform. If you touch the rib of the prefabricated perforated plate, it is the place where the prestressed steel wire is set. When drilling, it is easy to drill through prestressed steel wire, which will destroy the stress of the floor, lead to the fracture and collapse of the floor, and cause greater danger. Therefore, holes should not be drilled in precast slabs.

What is the installation tutorial of aluminum honeycomb panel ceiling? What are the precautions for ceiling installation? The steps of ceiling installation are quite reasonable, and each item is clearly marked. However, personal understanding of this aspect is still complicated. If conditions permit, it is still necessary to find professionals to operate. You can pay more attention to various precautions in ceiling installation, remember clearly by yourself, and follow-up treatment can avoid more problems.