Specification for wooden doors

The standardization of wooden doors and home improvement construction are the most important steps in the whole family decoration process. The quality of the door should meet the relevant requirements, and the material of the door must be the specified material. Wooden doors are suitable for people, commercial buildings and houses. Then let's look at the specifications of wooden doors.

Specification for wooden doors1i. Installation of door cover

1, door cover assembly joint, should be tight, smooth, no black seam, fixed connector should be locked;

2. Diagonal lines should be accurate. When the height of the door piece is less than 2m, the error should be less than1mm; If it is greater than 2m, the error shall be less than1.5mm; ;

3. After the door is assembled, it should be vertical and horizontal, with a verticality tolerance of 2mm,1mm; For horizontal straightness;

4. The joint between the door cover and the wall should have fixing screws (not less than 3 per linear meter), and the width of the door cover should be greater than 20cm and fixed with iron plates;

5. Both sides of the gap between the door cover and the wall are sealed with styrofoam. Polystyrene foam should be evenly coated, dried and cut flat.

Second, the set of wire installation

1, set of wire installation should be evenly glued and fixed with the door cover and wall, and the set of wire interface should be smooth, tight and seamless;

2. If there is any gap between the group of wires and the wall, sealant should be used for caulking;

3. After installation, the sleeves on the same side should be on the same horizontal plane. Because the wall is uneven, the casing interface must be flat;

4. The allowable tolerance of the bending degree of the casing steel wire installation is within 65438 0 mm..

Third, the door leaf installation

1. After installation, the door leaf should be flat and vertical, and the exposed surfaces of the door leaf and door cover should be flat and level;

2. The door leaf is opened without noise, and the door leaf is closely combined with the sealing strip after locking, without swinging, and the switch is flexible;

3. The gap between the door cover and the door leaf is 6mm at the lower seam and 2mm at the other three sides. The allowable tolerance of all clearances is 0.5mm.

Fourth, hardware.

1, the door hinge should be vertical and flat, and the hinge fixing screws should be installed completely and flat and hidden in the hinge plane;

2, flat hinge should be in the door leaf, door cover corresponding groove, notch should be standardized, the size is the same as the hinge, trilateral tolerance is 0.5mm, flat and seamless after assembly, hinge opening should be flexible. The trident hinge should be installed according to the mold, and the bolts should be inserted in place;

3. The door lock shall be installed securely, unlocked freely without abnormal sound, and the slot shall be accurate and standardized, and the size shall be consistent with the lock body and locking piece;

4, accessories installation is complete, the fixing screws should be installed completely and straight;

3, suction, door closer, handle, etc. Should be installed in the designated location, the installation should be firm. The fixing screws should be installed completely and straightly, and the installed accessories have good effect.

Verb (abbreviation of verb) appears.

1, sleeve, door line and ground seam gap should be less than 3mm, and sealed with waterproof sealant gap;

2. After installation, the integral door should be flat and uniform, open freely and flexibly, and the overall effect is good.

3. The wooden door has no carved scratches and no paint.

Specification for wooden doors 2 Specification for installation and acceptance of indoor wooden doors:

1. After the door cover is installed, the joints shall be seamless, tight and dense. Door hinges should be vertical and straight, and the hinges should be flexible when opening and closing. 2. The slotting of the door lock needs to be accurate to ensure the normal opening and closing of the door lock. 3. Check whether the door leaves open and close flexibly and whether there is abnormal sound. From the overall appearance, the gap between the door leaf and the ground is within 3 mm.

What is an indoor wooden door?

1. According to the material and construction technology, wooden doors can be divided into solid wood composite doors, solid wood doors, paint-free doors and molded doors. Check the specifications, opening direction and related accessories of the door according to the design drawings, and measure the height and width of the door opening with a tape measure. The standard height and width of the door are 200cm×80cm, and the height and width of the bathroom door are 200cm×70cm.

2. Solid wood composite doors are made of wood, and door panels can be made of various materials and methods. According to the type and technology of doors, there are flat doors, core doors, all-glass doors and semi-glass doors. Flat doors are closed, without perspective light, and are mostly used for home doors and bedroom doors. This kind of door can be engraved with concave lines or convex lines, which is beautiful and elegant and has good integrity.

3. Solid wood doors are made of natural logs, which are processed by drying, planing and high-speed milling. According to the different structure of wooden doors, wooden doors can be divided into all-solid wood mortise and tenon doors, solid wood composite doors and plywood molded hollow doors. According to the classification of decorative materials, wooden doors can be divided into three types, namely, wood veneer, wood-based panel and polymer material, with code names M, R and G respectively.

Wooden door specification 3 wooden door acceptance criteria:

1. The entire door surface is free of scratches, bumps and other damages.

2. The color meets the customer's requirements, and there is no obvious color difference. Bright colors and clear wood grain.

3. The color of the whole batch of doors is consistent, and there is no obvious color difference. Meet the requirements of customer luster.

4. The paint surface is free from sagging, shrinkage, edging and wrinkling, and the line angle is basically the same as the surface, and there are no defects such as paint accumulation and scratches.

5. The size of the whole door is consistent with the size of the hole.

6. Both sides of the wooden door have the same color, and there is no obvious difference.

7. The coating surface has no obvious processing marks and no coloring defects.

8. According to the drawings and processing technology, the product is genuine.

9. Wooden doors should be smooth, square and without warping. Meet the tolerance requirements (national standards).

10. The combination between product parts should be tight, firm, seamless and inactive.

1 1. Hinge installation is not skewed, punch holes according to the mold, and the keyhole position is accurate.

12. Uniform line shape; The notch depth is consistent, and there are no waves.

13. The installation gap of the door panel is uniform and meets the requirements, and the door cover installer is not skewed.

14. The door leaves can be opened flexibly and freely without abnormal sound.

15. The door cover and both sides of the wall are sealed with sealant, dried and cut flat.

16. There shall be no less than 3 fixing screws per meter between the door cover and the wall.

17. The sleeves on the same side should be on a plane, and the gaps should be filled with sealant.

18. The sleeve joint must be straight, and the allowable tolerance of sleeve bending is 65438 0 mm..

19. After the door leaf is locked, it is closely combined with the sealing strip and does not swing.

Appearance:

1, casing, door line and ground joint gap should be less than 3 mm, and sealed with waterproof sealant.

2. After the whole door is installed, it should be flat and even, open freely and flexibly, with good overall effect and no scratches.

Standard:

1, the selected wood varieties and material grades should meet the design requirements. When the material grade is not specified, the quality of wood used for all-wood tenon joint doors shall comply with the provisions of GB502 10 -200 1 Appendix A.

2. The moisture content of the selected wood should not be greater than 12%. In high humidity areas and high humidity months, the allowable value of water content can be slightly larger, but it shall not be greater than the local equilibrium water content in that month.

3. The medium density fiberboard shall meet the first-class requirements specified in GB/T11718-1999, with a density of not less than 0.68g/cm, uniform distribution and stable texture.

4. When selecting particleboard, it should meet the requirements of GB/T 4897-2003.

5. Plywood should meet the first-class requirements specified in GB/T 9846. 1 ~ 9846.8-2004.

6. The formaldehyde emission of various glulam should meet the requirements specified in GB 18580-200 1.

7. The limit of harmful substances in adhesive shall meet the requirements specified in GB 18583-200 1.

8. The limit of harmful substances in paint shall meet the requirements specified in GB18581-2001.