How to tie the hook? Several correct knotting methods.

How to tie a hook and a fishing line (with pictures)

The method of knotting various knots is very important. If the buckle is not good, the fish will run away, or the hook and pendant will be lost, which is something fishermen don't want to happen. Here are some common knots.

(1) Toggle: Toggle is elastic and easy to untie. Commonly used are 8-shaped buckle, spiral buckle and cow buckle.

① Figure-8 buckle: thread the fish thread through the ring, then pull it out over the length of the figure-8 buckle, tie it with its double thread into a figure-8 buckle, and then tighten it.

(2) Screw buckle: thread the fishing line head through the loop 4 ~ 5cm, wrap the fishing line with the thread head for 5 ~ 6 turns, then pull the remaining line onto the loop, fold the thread head pair into a sleeve in the sleeve connected with the loop, and then tighten the line to tightly clamp the sleeve inside.

(3) Tie the bull buckle: thread the fishing line through the ring, hold the fishing line with one hand, wrap the fishing line around the fishing line with the other hand, pull it out of the looped fishing line, then thread it into the ring, and finally return along the threading direction, leaving a sleeve to tighten the fishing line.

(2) Dead button: Dead button means that after the button is tied, it will be pulled tighter and tighter, and it will not be loosened due to the force of the button, such as pig's trotters, repeated buttons, single set of buttons, etc.

① Pig's trotter buckle: wrap the thread head through the thread for two times, cross the thread head with the other end of the thread head in the middle of the two thread rings, and then tie a common buckle on the thread head.

② Repeated buckle: This buckle can be used to connect the main line with the main line, and the main line with the branch line. When knotting, the two threads are parallel, and the two wells are wound into a common buckle, which is repeated for 2 ~ 3 times and tightened each other.

③ Single-set buckle: Fold the fishing line into a circle, and the other end passes through a circle in the circle to form an ordinary buckle, then put your finger into the small circle, and tighten the two wires with the other hand. Finally, insert the Jun Jun or a metal ring with a dead knot and tighten it.

Finally found a detailed knot method, make it up:

How to tie a hook and a fishing line (with pictures)

The method of knotting various knots is very important. If the buckle is not good, the fish will run away, or the hook and pendant will be lost, which is something fishermen don't want to happen. Here are some common knots.

(1) Toggle: Toggle is elastic and easy to untie. Commonly used are 8-shaped buckle, spiral buckle and cow buckle.

① Figure-8 buckle: thread the fish thread through the ring, then pull it out over the length of the figure-8 buckle, tie it with its double thread into a figure-8 buckle, and then tighten it.

(2) Screw buckle: thread the fishing line head through the loop 4 ~ 5cm, wrap the fishing line with the thread head for 5 ~ 6 turns, then pull the remaining line onto the loop, fold the thread head pair into a sleeve in the sleeve connected with the loop, and then tighten the line to tightly clamp the sleeve inside.

(3) Tie the bull buckle: thread the fishing line through the ring, hold the fishing line with one hand, wrap the fishing line around the fishing line with the other hand, pull it out of the looped fishing line, then thread it into the ring, and finally return along the threading direction, leaving a sleeve to tighten the fishing line.

(2) Dead button: Dead button means that after the button is tied, it will be pulled tighter and tighter, and it will not be loosened due to the force of the button, such as pig's trotters, repeated buttons, single set of buttons, etc.

① Pig's trotter buckle: wrap the thread head through the thread for two times, cross the thread head with the other end of the thread head in the middle of the two thread rings, and then tie a common buckle on the thread head.

② Repeated buckle: This buckle can be used to connect the main line with the main line, and the main line with the branch line. When knotting, the two threads are parallel, and the two wells are wound into a common buckle, which is repeated for 2 ~ 3 times and tightened each other.

③ Single-set buckle: Fold the fishing line into a circle, and the other end passes through a circle in the circle to form a common buckle, then put your finger into the small circle, and tighten the two wires with the other hand. Finally, insert a Jun Jun or a metal ring with a dead knot into it and tighten it.